Honda clone help

Status
Not open for further replies.

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i know which way the jet went in, so on the end of the tube, theres the little hole and the big end, so i alligned the little hole to the get and put it up into the carb. and what would be a fix for the float/neddle problems?
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
the floats on right, im sure. and the needle is in, it gets gas, i did notice a small leak today,coming from inbetween the block, and the carb, is that the problem?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Fuel leaks are not generally considered "normal". Your gasket is bad, amongst other things.

Take the bowl off and check the float. Make good and sure it is installed correctly. Make sure the needle is seating properly, and is properly retained to the float with the spring clip. Make sure the float is able to function smoothly without hanging on anything. Make sure the float height is set according to spec. Lastly, be sure to install the bowl facing the right way, ie drain plug toward the hinge side of the float.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
where would i get the gasket? cant i make my own? and the float dosent get hung up and is retained, float is to height, and thats where i was at during reinsstallation of the bowl, it always looked like both ends went stright in a line, but when i took it off, the main was to the side and the other was to the left, which is how i have it now,
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Yes, you can make the gasket. I hear cardboard cereal boxes work. You can also buy gasket material in sheets at auto parts stores, which is what I do.

Also make sure the carb is not "loose" when mounted.

If it's not the gasket, then fuel is pouring out the vent, again pointing to a severe flooding problem- likely indicating the float and needle valve.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i turned the bowl the opposite way and well, i seemed to keep it running, i got it to start and held the throttle a little bit above usually starting and it ran, but one thing, is 1, a little bit of gas was coming from inbetween it in the gasket, but its getting fuel, and 2, it was smoking from the exaughst, would that still be a gasket problem?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Offhand, I'd say it's running rich. Now, you put in a larger jet based on what? A better air intake and nothing else? I'm thinking that jet's too big. But before we go there, I'm gonna ask this <again>. Did you have everything running PERFECTLY in stock form before throwing all the parts in the air?
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i was researching and most people recomended a number 90 jet, so thats what i got, its got a better air intake, and a header with muffler, and it ran great stock only problem was the oil sensor, then i broke the chain, but it still ran good, then i put on the air intake, and it ran, then we ran into the governor linkage problems, got that back together and it worked good, but wouldnt run off of choke, and then i put my header on, it ran good but still has to have choke, then finally, i did my re jet to number 90, and now its just ****ty, i have to pull alot for it to even try to turn over, and when it does i have to instantly put the throttle a little higher and it smokes like crazy. theres drips between the carb and block,and i was to stupid to get the extended warranty
 

devino246

Official DIYGK Chem Nerd
Messages
3,856
Reaction score
17
Location
Lynchburg, VA
i was researching and most people recomended a number 90 jet, so thats what i got, its got a better air intake, and a header with muffler, and it ran great stock only problem was the oil sensor, then i broke the chain, but it still ran good, then i put on the air intake, and it ran, then we ran into the governor linkage problems, got that back together and it worked good, but wouldnt run off of choke, and then i put my header on, it ran good but still has to have choke, then finally, i did my re jet to number 90, and now its just ****ty, i have to pull alot for it to even try to turn over, and when it does i have to instantly put the throttle a little higher and it smokes like crazy. theres drips between the carb and block,and i was to stupid to get the extended warranty

I wouldnt go off what others have used for jetting simply because jetting is different depending on elevation and season. Someone on the coast of Alaska in winter will need a much larger jet than someone in Denver in summer because the air in Alaska is denser.

I just took my jet out and ran a small, diamond-tipped dremel bit through by hand till the engine was running right.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i have no drill or bits, there all at my dads house, where i cant go, well im in michigan in between winter and summer ish, so i went with 90. but i guess i was wrong.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
take the old gasket out, trace it on a piece of cereal box, and punch the holes with a craft hole puncher.

never had a problem if you make it right.


put the stock jet back? or bore it out a little with anything you can find, say, wire?
 

Gillgamesh64

New member
Messages
200
Reaction score
0
Location
Griffith NSW Austraila
between the carb and the block is very important! It hast to be a perfect seal take the carby off and replace the gasket use some fuel impervious gasket sealant, There are hundreds to choose from! Than tighten it all up properly!! Leaking fuel is bad and air get in between carb and engine is terible it cant run like that!!
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
alright ill do that, and i would but, when i went up to the lawn and garden shop for fuel hose, i just brought the hole thing with me, i asked her a better way to get the jet out, because it was tight, for some reason, some bolts are factory tight that ive never taken off, and some are loose ive never taken off, and well anyway, she ****ing destroyed the jet, it looks terrible, i dont think itd be a good idea to put it back in, and make the hole bigger? IM me on aim
 

Gillgamesh64

New member
Messages
200
Reaction score
0
Location
Griffith NSW Austraila
Can you get some engine silicone or something, most old guys carry stag glue around in there tool box it will work fine so ask to use a bit from some one or steal some from your uncle lol but get something, undo the carb and inspect the gasket be very gentle and the gasket may even be usable but if it is ****ed than out with the cerial box, cut the gasket with a sharp knife in one continouse motion jaggard eges blow out first also use a punch for the bolt holes it works the best than cover it in the glue you stole and bolt up tight.... If you cant steal any glue than smother it with grease instead!
 
Status
Not open for further replies.
Top