HF Predator Sale?

Status
Not open for further replies.

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
Hope he can get out before they become their own country...
He can't.


The one with the pants won't let him!!! :p
D0h!
 
Messages
357
Reaction score
7
Location
Dallas, TX
Any coupons on the 212 this month? The 20% off coupon no longer works, I uses I have to wait for the super coupons to get a sale on one.

--Dan
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Any coupons on the 212 this month? The 20% off coupon no longer works, I uses I have to wait for the super coupons to get a sale on one.

--Dan

Yes
Hold on a second... There it is! Good to 1/15/17 6 days Shop Now!!
 

Attachments

  • 99.00.JPG
    99.00.JPG
    89.8 KB · Views: 10

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I believe. It is easier to get Over 8HP out of a 212. Then mess with the 1" shaft on a 301.
More expensive Clutch and TC!
Limited Aftermarket parts.
You need Big block motor plate for a measly extra 89cc.

Not worth it even at 85 bucks. IMHO
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
8hp to 6.5 hp is less than 20% increase not 30%
A 212 with intake exhaust and rejet makes like 10hp with parts easily found

NR Racing no parts for 301cc
ARC racing no parts for 301cc
???I dont want to be stuck at 8HP and have to buy a $125.00 1" clutch.
 

Hellion

Staff Murderator
Messages
9,443
Reaction score
4,369
It's more like an increase in available torque--the 8hp will get you up the hills with less wheezing. Show me that the 8hp actually revs higher though.

Have to agree with Chancer. As sad as it is, there's no aftermarket 'go fast' support for these Chinese engines above 200-212cc. Hard to justify having one.
 

B_Bimmer

Member
Messages
200
Reaction score
1
Personally since I refuse to dump more in aftermarket parts than the engine cost I had no problem justifying several. I understand the limitations though and do not blame anyone for taking a pass.
 

MrC.

Member
Messages
238
Reaction score
0
Location
florida
I have been looking at the 420cc. Thats a big jump amd might justify the tav for the one inch. I need to buy an engine anyways. Any thoughts on the 420?

Mrc.
 

AltuveRules

New member
Messages
57
Reaction score
0
Location
New Braunfels Tx
Chancer said:
8hp to 6.5 hp is less than 20% increase not 30%
A 212 with intake exhaust and rejet makes like 10hp with parts easily found

NR Racing no parts for 301cc
ARC racing no parts for 301cc
???I dont want to be stuck at 8HP and have to buy a $125.00 1" clutch.

It depends. Exaust/intake and a rejet could easily be managed with a 301 and would push more power than a 212 with the same. There aren't racing parts, but if one doesn't want to throw hundreds at it who cares. After the easy mods, the 301 might surpass 11hp limit of the 1" tav2, in which case you'd need a 40 series but they're only like $40 more and it would be worth the 10% overdrive anyway. With racing parts in a 212 (which is the only point of getting one) you'd need a heavier duty tc pretty soon anyway. So to conclude: 301 has more easy power, but less overall potential.

There's no replacement for displacement

---------- Post added at 11:34 AM ---------- Previous post was at 11:03 AM ----------

You would have to figure out how to mount the 40 series though as the ebay one doesn't have a backplate. Still, the 310 is ~$30 cheaper (usually no tax on ebay :thumbsup:) and you'd make power that would take racing parts on a 212.
 

Randy H

New member
Messages
892
Reaction score
29
http://www.nrracing.com/product-p/stage3kit270.htm

40 series clutch about $95 on Amazon. Worth that for the performance increase, even though as profit posted, not hard to find a 30 series 1".

I don't think it would be hard to make a mounting plate. Mr. Spindle recently posted a link on that. Some plate and a tube 1 5/8" .120 wall. Lotsa ways to go here. Pillow blocks, flange bearings.
 

AltuveRules

New member
Messages
57
Reaction score
0
Location
New Braunfels Tx
Randy H said:
40 series clutch about $95 on Amazon. Worth that for the performance increase, even though as profit posted, not hard to find a 30 series 1".

I don't think it would be hard to make a mounting plate. Mr. Spindle recently posted a link on that. Some plate and a tube 1 5/8" .120 wall. Lotsa ways to go here. Pillow blocks, flange bearings.

Exactly what I was saying :thumbsup:
 

Joe-405

Enjoying New Projects
Messages
2,673
Reaction score
98
Location
U.S.A.
New super coupons for BOTH engines !!!!!
 

Attachments

  • IMG_20170127_202534.jpg
    IMG_20170127_202534.jpg
    344.3 KB · Views: 7
  • IMG_20170127_202514.jpg
    IMG_20170127_202514.jpg
    612.2 KB · Views: 4

Joe-405

Enjoying New Projects
Messages
2,673
Reaction score
98
Location
U.S.A.
Yep just in time for the new buildoff season also ! And I voted for.you also and me of course. Good job. I'm gonna concentrate on 88mph and skip the buildoff. The 3 years in a row wore me.out and I need to go faster. Hahaha
 
Status
Not open for further replies.
Top