Hemi maximum compression

Status
Not open for further replies.

matiask1

New member
Messages
38
Reaction score
0
Location
Santiago,chile
Hello
Im building an engine and I want to have te maximum compression I can possibly get like 12 to 1 or 11 to 1 but I dont know what head ,cam ,piston, valve size and milling do I need so please help. Im running 97 fuel.:thumbsup:
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
Hi, not trying to be a jerk, but the best thing you could probably do would be read up on the predators that others have built here. Bob580 has a very comprehensive thread on here about his build with pretty much every formula and calculator you'll need to get where you want to be with yours. It's much better to understand why you're doing what you're doing than to just follow a recipie since old so and so said it would work.

http://www.diygokarts.com/vb/showthread.php?t=32385&highlight=Advanced+hemi
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
+0.020" rod
Stock flat top piston.
Black Mamba Jr Cam.
Hemi Head Milled about 0.050"
8 degree offset timing key
26lb valve springs
Gx390 carb
NR 2 piece zero degree carb adapter
0.026-0.028" idle jet
0.042" main jet
Weenie Pipe exhaust.
AR3910 or AR3911 spark plug
SS Valves

That is cliff notes version of my 80 page build.
If I had to do over, I'd mill 0.050".

You need to measure some things.
Piston to deck height,
Piston to valve clearance.

Take off the head, and get a feeler gauge and straight edge.
Measure how far in the hole the piston sits at TDC.
Get some clay and google how to measure piston to valve clearance.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Ummmm....somebody correct me if I'm wrong, but I think thats too much compression for 97 octane.

Perhaps you can play with the timing and make it "work"... Buy I think it's not ideal.
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
I used to drive my 12.8:1 malibu back and forth to work when gas was still red, 101 at any premium pump, and $0.89/ gallon.
That engine would self destruct trying to run it on today's pump gas.

Fwiw, I agree that at 12:1 he'd be pushing the limits of 97 with an experienced tuner.

But hey, horsepowers right?
 

Flyinhillbilly

The great cornholio
Messages
2,468
Reaction score
132
Location
North West Arkansas
I'd think so. Mine was at 11.8 and running like a champ with a LOT of timing on 100 so I don't see why 97 wouldn't work at 11:1.
It would probably work at 12:1, but the tuning window would be pretty small, you'd have to have it dead nuts tuned for it to live IMO.
 

Randy H

New member
Messages
892
Reaction score
29
I think the cam profile plays a big part in maximum compression. A stock or mild cam might be less tolerant of high compression ratios at certain octane levels.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
Stock cams don't have much overlap, which means there is high combustion pressure at low RPMs.A racing cam with more overlap will bleed off that pressure at low RPM. I run 100 octane with 11.1 : 1, black mamba Jr cam and 8 degree offset timing key. My NASCAR buddy tells me he ran 93 octane on his 12:1 car. But timing, static CR, and cam timing all matter. I use 100 to be safe. I might be able to get away with 93. I'd rather not know what pinging sounds like.
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
More timing needs more octane. Your cam shaft's cam card will specify what timing to use. Most cams want 32 degrees BTDC. An 8 degree offset key (or billet flywheel already timed) should get you close to where you want to be.
 
Status
Not open for further replies.
Top