Help with GoKart buggy!

Status
Not open for further replies.

brittanynh21

New member
Messages
3
Reaction score
0
Hi, I have a 250 cc Kart. Its leaking some milky whitish oil and spraying water. The pics attached shows where the leaks are coming from. I don't even know what the parts are called :huh: . BUT I CAN LEARN. I just got the Kart and the guy said all it needed was a new carburetor. after changing the carburetor, I put it in gear and it would go forward but grinded to go in reverse. After only going forward a couple feet it popped out of gear and now wont go into either reverse or forward. I left it running to see if I could see anything and noticed some white milky oil flowing from the left little box as circled in red in the picture attached. I checked the oil from the box to the right and cleaned the Sight Glass (BTW the oil was black and thick and the glass was caked on with oil). I found out that its supposed to be gear oil and so i am assuming that is the gear box.. (who knew! Hopefully y'all do because I didn't..... ) Anyway, if that is where the gear oil is and I know where the regular engine oil goes, then why is there milky oil leaking from the little box to the left?
Also, when the gas peddle is pushed, water sprays out from the other circled spot on the pic.
Any help would be great, even if all you can do is identify the names of the different parts on the pic. That way I can search it better.
P.S. Obviously I am no mechanic. I just bought this for my two boys and want to get it running for them. Thank you in advance!
 

Attachments

  • full rear view.jpg
    full rear view.jpg
    53.9 KB · Views: 24
  • Close-up oil leak.png
    Close-up oil leak.png
    157.3 KB · Views: 24
  • close-up water leak.jpg
    close-up water leak.jpg
    35.1 KB · Views: 17

B.M.800

TheBeal.
Messages
2,387
Reaction score
26
Location
Central PA
White milky oil means there is water in it. Probably a good idea to drain the oil from the engine, and gear box. Water in these things can cause big problems.

Can you shift the gearbox while the engine is OFF? It could be a problem with the clutch, if its not fully disengaged it could cause grinding. When you drain the gearbox, look for big chunks... that could cause grinding too.

Where its spraying water, it could be from sitting outside... or there could be a blowed gasket somewhere. That could explain why the oil has water in it.

Where its leaking oil, there should be a seal in there than can be replaced. If you can get it out without damaging it further, there may be some numbers on in. If your local auto parts stores are any good, they might be able to find a replacement.

Ofcourse this is just my thinking on the matter... Other may have more better ideas.
:cheers2:


Could we get a picture of the whole buggy?
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
the "long" part in the center (the one that's driving the wheels from it's lower end) is a forward-reverse gearbox.
The part that's leaking is the input shaft (likely popped it's oil seal)
OR which is indistinguishable for us, the OUTPUT shaft of the engine itself.
(again likely the oil seal)
the engine will likely be an CVT transmission 250cc four stroke (It reminds me of a klung motor from what little we can see in the pics)

Anyways, grinding noise..
chances are the new carb is idling too high and the clutch is trying to engage even if the buggy is still not moving.

lower the idle speed of the carb and try again!

If you still hear grinding noises, it's very likely the aforementioned Forward Reverse Gearbox.
unfortunately, you will need a complete maintenance kit (gaskets, seals, maybe even new gear wheels *shrugs*) to repair it..
and it needs to be uninstalled and disassembled to fix the issue (even if it's nothing but the oil seal) and that reads new gasket kit for reassembly is required.
OR you find a new one on ebay (or klung-motor.com if I'm correct with my assumption ;))

The watersprayer seems to be the cylinder base and yes,,, chances are there's oil mixed in.
(really it's hard to make out what part it is on those pics...)
to fix that.. again you will need a gasket kit, and the engine will need to be disassembled in order to remove the cylinder reseal the base and reinstall it.

IMHO previous owner knew and you've been cheated... but you're here now, and we can guide you through the repair if we get a much better view of the engine and kart (to identify the make and model and hopefully make and model of the engine and gearbox)

The problem is, even with our guide this repair is not trivial, it's certainly not a quick saturday evening project.
This is something you will be spending several days with.
And invest several dollars (sometimes hundreds even, depending on what tools you have and what you need to buy to succeed)

Again PO must have known this...

If you want to do this on your own, we'll provide all the help we can;
but this might be a case where you're better off giving this buggy a professional mechanic to have it repaired
(less chance of failure and depending on your tool supply, maybe not even more expensive)
ask one for a quote at least, just to know what you'd face worst case.

'sid

PS DO NOT RIDE THAT BUGGY or you could eventually destroy the engine, if there's oil in the waer, there will be water in the oil which is all but acceptable!
 

brittanynh21

New member
Messages
3
Reaction score
0
Hey ya'll sorry for not responding sooner. life...

B.M.800 : When I drained the gearbox there was some chunks but lots of small shavings.
A friend of mine came over and we took off the covering where the clutch is because that where the noise was. He said its a Centrifugal Clutch. My friend said the clutch must be bad in it.

itsid : its a Kandi KD-250E it says the engine family is (7kndx 250 gml) its a 2007. The numbers on the engine match the numbers on the frame.

Is there a way to know if the clutch is bad? I would put it in gear and it would move but once I pushed the gas a little it would pop out and make a loud grinding noise. Is there a way to tell if it is the clutch or in the gear box?

My plan as of now is to replace the engine block but I dont know whether to replace the clutch or if its something in the gear box or both..

Thank yall very much for all your help!!!!!!

Here is a video of it running.
https://youtube.com/watch?v=KH5W_z0FrUY
 

Attachments

  • 20170308_114840.jpg
    20170308_114840.jpg
    131.2 KB · Views: 1
Last edited by a moderator:

brittanynh21

New member
Messages
3
Reaction score
0
I posted a video at the end of my reply. please check that out I hope you can get a better idea. I did the lowered the idle and that wasn't it. I am working on another video to try and make it easier for you to see. Thanks again.
 

ultralight01

Senior Yet Young Member
Messages
619
Reaction score
5
Location
Hood River, OR, In a galaxy far far away
If you can "put it in gear" and it doesn't just go when you rev it, it's not a centrifugal clutch.

If it's brand new, shavings in the oil are common for the engine. The clutch gear has probably been shredded. Dig deeper and take some photos of the inside of the clutch and we could help you some more. Then it's a matter of research to find out where to buy a replacement part.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
I hope the "FS" is identical to you "E" enginewise

here's the page you want to bookmark
http://www.kandiusa.com/productp.php?id=15&ssid=235

the oilseal is the only part I think you will need, that's actually in the list.. no gasket kits no nothing;
but I'd hope you can ask them for help and how or where to source the parts you'll need.

Oh and in case you wonder.. people's eyes are horizontally aligned, not vertically..
just in case you wonder which way around a video should be taken ;) *cough*

Aanywhoooo.. do NOT run the engine excessively, do not rev it more than absolutely necessary (at best never ever even start it again before your waterleak is resolved for good!)
chances are that gasket not only popped into the great wide open we call "outside", but also into the tiny little "inside" of the cylinder..
and if so, revving the engine will ruin the cylinderwall and the piston thanks to the lack of protective oil.
So yeah... be carefull, one revolution will be the last, and I cannot tell you which one it'll be :(
This must be fixed in order to securely run the engine.

I'm sorry, fixing the clutch issue (if you have one [issue.. not clutch;)])
now is just -forgive me- stupid.
In order to tell i the clutch needs to be replaced it idle speed needs to be adjusted;
in order to adjust the idle speed the engine will need to run,
in order to run the engine it'll need to see a repair FIRST.

So yeah, there is a way.. NO you should NOT fix it just yet..
since once that's working there is no way your kids will NOT want to ride a few minutes;
and frankly you'll give in after a few days of being pested by them..
and then the engine locks up on them and up to 1500 bucks are needed to buy a new engine ...

Again, I'm not trying to scare you off, I'm tying to save you as much hassle and costs as possible.
and that can ONLY be achieved by fixing minor issues NOW; before the engine decides to spend the rest of it's life as a paper weight.

Yes, it's a lot of work, yes it'll cost you some money and time..
and no, I'm afraid there is no real option :(

'sid
 
Status
Not open for further replies.
Top