Help with 30 COmet Clutch Settings with HF Engine

Status
Not open for further replies.

sawood711

New member
Messages
10
Reaction score
0
Location
Owings, Maryland, USA
I purchased the Black Widow Go Kart made by ASW from someone locally and the engine was in bad shape. Instead of throwing the $30-50 into fixing it I decided to buy the HF Predator 212cc special for $99. The 30 series Comet clutch was pretty dirty and one of the springs was not there. In the rear pulley it has the green spring in it I believe. I am not sure what gears the sprockets are as well.

My question is what color spring(s) do I need to buy to replace the broken set? I am not sure what color spring would work the best with this engine to provide the best power output for my kart. Also, should I keep the green spring in the back or upgrade to the yellow/gold one?

I am mechanically inclined and use to race go karts back in the late 90's and early 2000's, but we didn't run this style clutch. Any help would be greatly appreciated on which spring to buy and how to achieve the best setup. At this time I am not looking for any performance mods just yet. I am trying to teach my daughter how to drive and maybe in a year or two I might step it up and rebuild the motor for more power.
 

cavfire

Member
Messages
110
Reaction score
1
Location
auburn, georgia
Blue tipped garter springs are the original color. White tipped springs are good if you start modifying the motor. Performance mods have a habit of raising the powerband, so engaging at a higher rpm helps.

Green spring on the driven is usually in the middle hole and can be moved to the #1 hole iirc to delay the upshift which helps if you ride in hillier terrain.
 

sawood711

New member
Messages
10
Reaction score
0
Location
Owings, Maryland, USA
Thanks for this! So I ordered a 5959 belt for it, but the belt that came is a bit short. Is 5959 just a designation for a style of belt and if so, where can I find the right belt for my kart?
 

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
Any comet 30 series belt will work, they are all the same length, I get mine from Amazon for 12 bucks.

My local Tractor Supply caries them also, at 30.00 bucks.
 

cavfire

Member
Messages
110
Reaction score
1
Location
auburn, georgia
Hey sawood by hook or by crook I was able to get that same belt on. Thinking I opened up the driven a bit. A tad snug when it first went on, but not to the point you couldn't crank the motor or anything. Doesn't take long for the belt to get enough wear to make it easier to put on.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Any comet 30 series belt will work, they are all the same length, I get mine from Amazon for 12 bucks.

My local Tractor Supply caries them also, at 30.00 bucks.

You are SERIOUSLY misinformed. They are NOT all the same length. Please do not tell people this. There are different belts for different distances between the driver and driven. Have a look at this chart to see what belts are required for which distance

http://www.gokartsupply.com/tcbelts.htm

Well I bought this one from Amazon and it didn't fit. It was a bit short.

http://www.amazon.com/Drive-Replace...UTF8&qid=1460418002&sr=8-4&keywords=5959+belt

I'm going to send it back and try another one. Does anyone have a link on Amazon that will work?

Have a look at the link i provided above. Measure the center to center distance between your driver and driven and then try match that to the belts on the chart. You will also need to know the diameter of your driven
 

sawood711

New member
Messages
10
Reaction score
0
Location
Owings, Maryland, USA
Well I have two Karts that I bought and the first one, which is an older Manco with a 5hp Tecemseh engine, runs just fine and has the same size belt as the Black Widow kart that I just bought. The belt was labeled with a 5959, so that's the belt I bought off of Amazon. Is the #5959 just a reference number or style of belt and not the actual part number for the belt? The Manco kart just needed general maintenance and did not need any new parts. I have owned both of these karts for just over a week now. Such a big learning curve coming from my racing days. Thanks for everyone's input so far.
 

Attachments

  • image.jpg
    image.jpg
    473.1 KB · Views: 3
  • image.jpeg
    image.jpeg
    344.6 KB · Views: 3

Jrgunn5150

Rudderless
Messages
1,028
Reaction score
12
You are SERIOUSLY misinformed. They are NOT all the same length. Please do not tell people this. There are different belts for different distances between the driver and driven. Have a look at this chart to see what belts are required for which distance


Well i guess I got lucky then lol :roflol: I just put comet 30 series belt in Amazon and bought the first one that came up lol.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Well i guess I got lucky then lol :roflol: I just put comet 30 series belt in Amazon and bought the first one that came up lol.

Yes, you were lucky. That doesn't mean that you still don't have the correct belt. Your kart may be under performing without you even knowing. Maybe check to see if you have the correct one
 
Status
Not open for further replies.
Top