Gx390 engine problem need help diagnosing.

Status
Not open for further replies.

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Bought used gx 390 rust in gas tank. Cleaned carb, cleaned fuel line. New gas.

Starts fine. Idle adjusted to high rpm. After warms up died when you go to wide open throttle. Cleaned carb again, repeatable.

Engine backfires out of carb/intake, slamming choke to on position, kills engine every time.

I manually hold choke from doing this and it still bogs at wot and revs down.

I thought it was carb at first, possibly water contaminated gas but now I'm thinking it could be something else.

Any thoughts on diagnosis?
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
by the description I say you have a plugged channel in the carb..

you sure you poked every little bore, cavity and jet there is?

In this case:
pilot jet,
pilot air path,
pilot screw as well as
main jet,
e tube and it's air passages

backfires can be a sign of overheating the engine (mix too lean...)
but that'd mean the plug reading could tell you for sure it's the carb.

So check your plug and see if it's crusty already or just white.

if it is, sorry Grant, back to carb cleaning it is :(

If it's NOT and the plug looks good, then your valve timing is off (or the intake doesn't close properly)..
either one of the rockers slipped and all you need is to pop open the valve cover to check seating, valve lash and maybe fix.
[on the other hand it shouldn't idle fine then... right? ANYWAYS]

Or someone messed with it the hard way, and the cam is off, maybe a lifter binds or a pushrod is bent.

Personally, I'd read the plug and if in doubt clean the carb again ..
but while it soaks I'd check under the valve cover if I see something odd.
And if not and the carb clean still doesn't help, pop the case open and check the cam

'sid
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
Only other thing I could think of would be fuel delivery from tank to carb. I always seem to suggest what I think MY issues are. LOL

Gas Tank Venting? Needle valve issue?
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Needle is good. Since water was in the tank, the carb has that white oxidation stuff in it. I sprayed out EVERY hole etc multiple times. I'm going to order new tank, filter, fuel line, and carb just because of the visible rust and oxidation.

I am also going to pull the head, inspect rods, valves, crank key, lap valves and set lash just to be thorough.

I'm still wondering why did the backfire out the intake occur every time?
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I think (someone correct me) that usually a carb backfire is a timing issue. ?
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
I think (someone correct me) that usually a carb backfire is a timing issue. ?

well if the valve seat properly, yes.. timing issue..

if the intake valve doesn't close properly it'll backfire each and every time, even if the timing is correct ;)

Oh Grant.. I'm not sure spraying the carb alone can remove all those nasty oxidation... (yeah I still call it rust personally :D)
I think you should add some poking action to the cleaning process; just to be sure.

'sid
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
cylinder wall was pitted everywhere, don't even care about the carb now because im getting a mikuni and the one I ordered from china came as a handheld throttle mechanism seriously thanks china.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
ouch..

but isn't it all the same.. I mean the throttle cable slots right under the cap...
well the spring behidn said cap... aaaaanyways,

it should be convertible in practically no time at all (undo cap, unhook cable end, insert new cable end, rescrew cap)
Or are we talking about different mikunis here?

'sid
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Instead of getting a carburetor from China, I got a handheld throttle mechanism with no carburetor.
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
Instead of getting a carburetor from China, I got a handheld throttle mechanism with no carburetor.

Oh.. wow, that is indeed off by a few...
ebay? maybe babelfished description?... too bad.

Anywhoo, good luck for the next try.. maybe you now get an airfilter adapter instead :lolgoku:

'sid
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
It's rare that any small engine backfires:(


Want some video of my nephews Baja when I let off the gas?

"In general, backfiring on deceleration (as opposed to acceleration) is generally caused by a lean condition in the pilot circuit. What happens is that the mixture leans out enough to where is fails to ignite consistently. This, in turn allows some un-burnt fuel to get into the exhaust pipes.
 

Jfive

New member
Messages
645
Reaction score
1
Location
Great falls Montana
I tend to click the U.S. Only button on eBay and buy the China stuff from a U.S. Seller in California. Usally California, sometimes another state. I made one of the cables from the bike cable kit from Walmart fit my China keihin carb. Link the eBay ad? Nice is the best approach for refunds or re shipment on eBay I've found. I yelled at one seller that stole my money and that got me no where. It was unfortunately before PayPal and I used a money order, but still. eBay didn't help me either. Hope you get the carb or refund then buy proper carb.
 
Status
Not open for further replies.
Top