Gx270 clutching

Status
Not open for further replies.

Drifttriker

New member
Messages
5
Reaction score
0
Location
Denmark
I am currently building a Drift trike, using honda gx270 engine, however the dude i bought it from removed the clutch before sending it. Im new to go kart building, and i was wondering which kind of clutch would be preferable, since i dont want any gearing on it.

Also, if you know somewhere to find these things to reasonable prices (i dont care if they are used) i would appreciate any help.

Thank you in advance.

Nicklas Pryds, Denmark
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Welcome to the forum, Nicklas

What you need is a 1" bore centrifugal clutch (copy & paste the bold text into google) similar to this...

As for where to find one, that sounds like a job for itsid; he;s from Germany so , he would have a better idea than most of us...

In the meantime, you can try ebay using the same search text...

Having said that, you said
I dont want any gearing on it.

There needs to be gearing of some description to transfer power to the rear axle; even a clutch, chain & axle sprocket (the bare minimum requirements) is considered "gearing"
 

Drifttriker

New member
Messages
5
Reaction score
0
Location
Denmark
Thank you Fabroman!

I've been looking around, and the clutching/gearing market confuses me a bit.

These are a couple of types i've been looking at:




But will the one on the bottom picture be sufficient?

Im sorry about the "beginner" questions, but I appreciate any help you can give me :)
 

Half-breeder

"Edit" button removed
Messages
1,686
Reaction score
9
A beginner AND building a trike?! This oughta be interesting...

Yes, that clutch will work (looks like it's for a 1" keyed shaft)... but ensure the type of chain you'll be using before purchase, cause you'll evidently have to match the clutch teeth spacing w/ the axle sprocket/gear, cause the chain connects the 2. The more/most common chain#s are #40/41 and #35... but there are several 'other' sizes aswell... there may be different more common ones on your side of the world...?
 

Drifttriker

New member
Messages
5
Reaction score
0
Location
Denmark
Well, you have to start somewhere ;)

As far as i understand this clutch will give me more speed at max torque, also, it should still be a faily soft clutch in since there wont be much weight on the shaft right?

About wether the clutch matches the sprocket on the rear shaft, as far as i can see, we have the same standards in Europe as you have in the US. And the sprocket matches the #40/41 :)
 

Half-breeder

"Edit" button removed
Messages
1,686
Reaction score
9
Not sure whatcha mean...? In 'my' head your describing a TC/CVT system... but none the less, that clutch you pic'd is the more widely used on trikes.

I personally am finishing up my trike build, and am using a TC/CVT setup instead of the centripetal clutch. It'll give me the ability of driving slow w/out burning up the clutch, more initial torque, and smoother initial acceleration, w/ the ability of changing topspeed (to a degree) w/ the change of a single C-type gear.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
But will the one on the bottom picture be sufficient?

...But, there's only one pic... :huh:

Im sorry about the "beginner" questions, but I appreciate any help you can give me :)

Well, you have to start somewhere ;)

Now read those two sentences together; we were all beginners once ;)

As far as i understand this clutch will give me more speed at max torque, also, it should still be a faily soft clutch in since there wont be much weight on the shaft right?

Well, directly, no (as far as gravity is concerned); indirectly (as far as propulsion is concerned), the weight of the entire trike & the rider rests on the engine PTO shaft, more weight = more necessary torque... but, with your engine, you should be ok ;)
 

Drifttriker

New member
Messages
5
Reaction score
0
Location
Denmark
Well, directly, no (as far as gravity is concerned); indirectly (as far as propulsion is concerned), the weight of the entire trike & the rider rests on the engine PTO shaft, more weight = more necessary torque... but, with your engine, you should be ok ;)

Alright, for some reason, i cant upload the other picture, however i bought the one you can see. For now it seems to fit, but the shaft is running counterclockwise :surrender:

I've made sure that the camshaft is aligned with the mainshaft (not exactly sure what its called in english, translate says "bended knot" but i cant imagine thats correct :idea2:

If you want, i can share weekly progress in here and you can give advice if you spot flaws etc?
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Alright, for some reason, i cant upload the other picture, however i bought the one you can see. For now it seems to fit, but the shaft is running counterclockwise :surrender:

I've made sure that the camshaft is aligned with the mainshaft (not exactly sure what its called in english, translate says "bended knot" but i cant imagine thats correct :idea2:

If you want, i can share weekly progress in here and you can give advice if you spot flaws etc?

Bended knot means "misaligned" .....my parents named me Ben D. Knot....

EDIT: I'm pretty sure you want "clutch" ,"engine" or "CVT" sprocket and "axle" or "drive" sprocket....as what you are describing is inside the engine itself.....
 

Drifttriker

New member
Messages
5
Reaction score
0
Location
Denmark
The main output shaft is meant to rotate counter clockwise :huh:

Ah ofcourse, i just confused for a second because my manual was english, and i swapped the names of the shafts around. Its clear to me now.

I just finished my main frame by the way, got a few pics of weldings and design. i'll post them later since they are on my phone :)
 
Status
Not open for further replies.
Top