GX140 modding

Status
Not open for further replies.

Oxymoron

Newbesque builder.
Messages
444
Reaction score
10
Location
Maryland
Just be careful drilling, go only one drill at a time, and take a plug reading between. If you go a little too big, you'll probably have to either get an emulsion tube with more holes, or just replace the jet to lean the mixture back out.
 

wall

New member
Messages
24
Reaction score
0
Location
Portugal
And what is the maximum rpm I can safely get out of this stock engine? Should I really remove the governor or adjust it higher until I mod it further?
 

Oxymoron

Newbesque builder.
Messages
444
Reaction score
10
Location
Maryland
You can get a little out of governor linkage adjustment, but not much.... a few hundred RPM maybe?

I know a lot of people remove the governor without replacing the connecting rod, flywheel, and valve springs... but that's your call. I'm going to do mine all at the same time, because one of my boys ride the bike the engine is on. I'm more concerned with the kids safety than I am my own :D

As has been explained to me before, valve flutter will keep your RPM's in the relatively safe range after removing the governor if you keep the stock valve springs. Just don't put heavier valve springs until you replace the connecting rod at least, and probably the flywheel too. Stock cast flywheels are subject to impurities/flaws, and can shatter at RPM's they're not designed for.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Just be careful drilling, go only one drill at a time, and take a plug reading between. If you go a little too big, you'll probably have to either get an emulsion tube with more holes, or just replace the jet to lean the mixture back out.

FWIW- I have in the past, goofed and overdrilled a jet. Twice, if I were to be honest. I'm gonna lie, and say "once". ;)

The once that I overdrilled, was because I thought I had a long way to go, and skipped drill sizes. You'd think that after I'd already made that mistake once, I wouldn't have done it once again! :roflol:

At any rate, both times that I did it once, I was easily able to solder the jet closed and re-drill it to the size I foolishly skipped. It worked once, and then it worked once again... :innocent:
 

Oxymoron

Newbesque builder.
Messages
444
Reaction score
10
Location
Maryland
FWIW- I have in the past, goofed and overdrilled a jet. Twice, if I were to be honest. I'm gonna lie, and say "once". ;)

The once that I overdrilled, was because I thought I had a long way to go, and skipped drill sizes. You'd think that after I'd already made that mistake once, I wouldn't have done it once again! :roflol:

At any rate, both times that I did it once, I was easily able to solder the jet closed and re-drill it to the size I foolishly skipped. It worked once, and then it worked once again... :innocent:
Oooh... solder. I wouldn't have thought to do that. Nice tip! I'm getting ready to re-jet my carb because I got a UNI filter, so I'll keep that solder tip in mind. I might screw it it up once.

Your once twice comment reminded me of Brian Fantana in the first Anchorman... "Sixty percent of the time, it works every time". :D

Just.....once right... not twice or 4 times.....once...... I just have to check on that......

:stir::stir:
Fifty percent of the time, it worked 100% of the time :D
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
You can get a little out of governor linkage adjustment, but not much.... a few hundred RPM maybe?

I know a lot of people remove the governor without replacing the connecting rod, flywheel, and valve springs... but that's your call. I'm going to do mine all at the same time, because one of my boys ride the bike the engine is on. I'm more concerned with the kids safety than I am my own :D

As has been explained to me before, valve flutter will keep your RPM's in the relatively safe range after removing the governor if you keep the stock valve springs. Just don't put heavier valve springs until you replace the connecting rod at least, and probably the flywheel too. Stock cast flywheels are subject to impurities/flaws, and can shatter at RPM's they're not designed for.

Perfect advice; where'd you copy that from? :D

One point you didn't include: it's much safer to remove the governor internals than to simply disconnect it; leaving the internals in place will cause them to shatter & destroy the whole engine...
 

Oxymoron

Newbesque builder.
Messages
444
Reaction score
10
Location
Maryland
Perfect advice; where'd you copy that from? :D

One point you didn't include: it's much safer to remove the governor internals than to simply disconnect it; leaving the internals in place will cause them to shatter & destroy the whole engine...

Hey! That's from memory! I learned from the best ;)

That's what I get for assuming... when anyone mentions removing the governor, I assume they mean everything. Definitely remove ALL of the internals, and plug the hole the little rod came out of. That's from memory too, not bad eh? :lolgoku:
 
Status
Not open for further replies.
Top