go kart stalling

Status
Not open for further replies.

stevenkra

New member
Messages
4
Reaction score
0
hey guys im new to this forum and i do not know lot about go karts but i just brought one the other day and it is a push stat one and when its on stand i can start it no worries but when i put it on a hill and get some one to push me its starts the as soon as i accelerate it stalls
 

devino246

Official DIYGK Chem Nerd
Messages
3,856
Reaction score
17
Location
Lynchburg, VA
Welcome to the forums.

Pics? What type/size engine? How many teeth on the engine sprocket and axle sprocket? What diameter wheels?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
Might be a good idea to warm it up first while off the ground.
Driving a direct drive kart requires a different driving approach.
Don't tromp on the gas pedal. Accelerate slowly until you get up some speed.
If possible, try to richen the fuel/air mix.
 

stevenkra

New member
Messages
4
Reaction score
0
i have put some pics up if i need to take any more please let me know on the third pic with the red circle im not really sure what the two things do the long one turns in or out and the little one turn 90degrees ether way thank you
 

Attachments

  • IMG_0289.jpg
    IMG_0289.jpg
    98.3 KB · Views: 16
  • IMG_0291.jpg
    IMG_0291.jpg
    121.2 KB · Views: 16
  • IMG_0290[1].jpg
    IMG_0290[1].jpg
    104.5 KB · Views: 18

T-man

New member
Messages
1,232
Reaction score
4
Location
Missoula,MT
A racer !!! I was thing of something differant, are you sure that your putting in the right type of fuel??
 

T-man

New member
Messages
1,232
Reaction score
4
Location
Missoula,MT
well not sure, I know that alot of guys on here that race use differant mixes of fuels based on the engines mods and stuff.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Might be a good idea to warm it up first while off the ground.
Driving a direct drive kart requires a different driving approach.
Don't tromp on the gas pedal. Accelerate slowly until you get up some speed.
If possible, try to richen the fuel/air mix.



Use Yamalube @ 20:1.

:iagree:

This is good advice.


i have put some pics up if i need to take any more please let me know on the third pic with the red circle im not really sure what the two things do the long one turns in or out and the little one turn 90degrees ether way thank you

The rear L-shaped handle is your High speed jet adjustment.
The front T-Shaped handle is your Low speed jet adjustment.
There should an H and L stamped into your carb to further confirm the high and low speed adjustment locations.

Screw them all the way in until lightly seated, and then try starting out with 1/4-1/3 turn out on your High, and 3-1/2 out on your Low. These are usually pretty close initial base-line settings, then you can experiment from that point for fine tuning.

You'll find lots of carb setting info here in this search link: http://www.google.com/search?source...=1T4GZAZ_enUS369US369&q=KT100+carb+adjustment

Your carb also has a "Pop off" adjustment setting, that may just need to be adjusted on yours.

These carbs also can get dirt inside and/or its very common to develop tiny cracks in the diaphragm that will keep them from working their best. Most any race kart shops sell diaphragm kits for under $10. You'll need to find the model numbers on your carb and you could order a kit from here: http://www.cometkartsales.com/store/carbs/carbpart.htm
 
Status
Not open for further replies.
Top