Go kart moves while idling XTK-710E

Status
Not open for further replies.

MalakyTags

New member
Messages
19
Reaction score
1
Hi everyone,

Please bare with me as I'm new to the hobby.

I purchased a Manco XTK-710E with a 10hp Subaru Robin engine this year. I'm having an issue where the go kart seems to want to move forward as soon as it's started. I jacked the kart up and took the following video to demonstrate.

https://vimeo.com/150144021

If anyone has any good information on how to fix this issue, I'd be greatly appreciative.

Thank you!


Sent from my iPhone using Tapatalk
 

MalakyTags

New member
Messages
19
Reaction score
1
I tried loosening the cable attached to the gas pedal but that did not seem to work. Does the engine sound like its idling too high?


Sent from my iPhone using Tapatalk
 

colestreasures

New member
Messages
465
Reaction score
1
Location
Kentucky
Idle adjustment and could also be the belt or even both idle and belt. To fast idle or belt to tight or a bad driver or driver needing some maintenance. Can cause these things.
Cole
 

MalakyTags

New member
Messages
19
Reaction score
1
I did loosen what I thought was the idle screw, and took some tension out of the cable. I actually thought I had taken it all the way down and still had the issue of the drive wheels moving. Upon further research I've seen some recommendations of taking the torque convertor (both drive and driven units) apart to clean and lube. Does this sound like a viable solution? Any recommendations on how to do this or direction on where to get good information on this type of maintenance is appreciated. Thank you in advance!


Sent from my iPhone using Tapatalk
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
I did loosen what I thought was the idle screw, and took some tension out of the cable. I actually thought I had taken it all the way down and still had the issue of the drive wheels moving. Upon further research I've seen some recommendations of taking the torque convertor (both drive and driven units) apart to clean and lube. Does this sound like a viable solution? Any recommendations on how to do this or direction on where to get good information on this type of maintenance is appreciated. Thank you in advance!


Sent from my iPhone using Tapatalk
this might help, but i seriously don't think you adjusted the idle screw. Id do that first. So the screw for the idle adjustment is black, and is on top of the carburetor (i believe) since you have a subaru engine, it may be different. So look from behind the engine onto the carb itself for a black screw first. This screw contacts the butterfly lever itself and keeps it from completely closing.

Heres the video I made that could help you.
https://youtu.be/a3FCcLlR-sg

If it were me, id check the moveable sheave on the drive unit, it should be somewhat recessed at the top of the bell sheave. I cant explain it well, but if you took a video of the drive unit so you can see through the 'V' while it was running, i coudl tell you if it was the driven unit not totally disengaged or not.

PS a symptom of being partially engaged (which it is probably doing) is a HIGH IDLE like everyone has been saying. Just adjust the idle please. It has nothing to do with the throttle lever, its a screw. This is a page for a subaru engine, scroll down to the bottom and you will see the screw, its not black on this particular carb, however, you probably have a bigger carb, this is just to demonstrate what you should kind of be looking for http://outdoorpowerinfo.com/repairs/subaru_robin_mikuni_27x-623xx-xx_carb.asp you shouldnt mess with the idle mixture screw (i hope you havent), only the idle speed screw.

Also, the belt looks ok, but just to be sure measure the center to center distance and make sure the belt matches.
 

MalakyTags

New member
Messages
19
Reaction score
1
this might help, but i seriously don't think you adjusted the idle screw. Id do that first. So the screw for the idle adjustment is black, and is on top of the carburetor (i believe) since you have a subaru engine, it may be different. So look from behind the engine onto the carb itself for a black screw first. This screw contacts the butterfly lever itself and keeps it from completely closing.

Heres the video I made that could help you.
https://youtu.be/a3FCcLlR-sg

If it were me, id check the moveable sheave on the drive unit, it should be somewhat recessed at the top of the bell sheave. I cant explain it well, but if you took a video of the drive unit so you can see through the 'V' while it was running, i coudl tell you if it was the driven unit not totally disengaged or not.

PS a symptom of being partially engaged (which it is probably doing) is a HIGH IDLE like everyone has been saying. Just adjust the idle please. It has nothing to do with the throttle lever, its a screw. This is a page for a subaru engine, scroll down to the bottom and you will see the screw, its not black on this particular carb, however, you probably have a bigger carb, this is just to demonstrate what you should kind of be looking for http://outdoorpowerinfo.com/repairs/subaru_robin_mikuni_27x-623xx-xx_carb.asp you shouldnt mess with the idle mixture screw (i hope you havent), only the idle speed screw.

Also, the belt looks ok, but just to be sure measure the center to center distance and make sure the belt matches.


Thank you KartFab for taking the time to provide such a detailed response. I'm going to spend some serious time this weekend working on my kart and will look at all of the options based on everyone's responses. I'll be sure to update the thread with my results. Again, a big thank you to everyone for your support!


Sent from my iPhone using Tapatalk
 

MalakyTags

New member
Messages
19
Reaction score
1
Happy new year everyone. As promised here is my update on this thread. The good news is I learned what and where my idle screw is. The bad news is the root of problem does not lie here. I proceeded to attempt to take my torque convertor off (in an effort to clean it) and quickly learned (at least believe I learned) that it cannot be removed without fully removing the engine from the frame. If anyone knows of a way to remove my TC without going to all this trouble, I'd greatly appreciate your input. Look at the initial video I uploaded and see where the TC is in relation to the frame and motor and you'll quickly see my issue. I removed the plastic fan and a few nuts but there still was not enough room to get the 2 units off of the rods that they sit on. Again, thank you In advance for any direction or support.




Sent from my iPhone using Tapatalk
 

MalakyTags

New member
Messages
19
Reaction score
1
Update - I figured out how to get both my drive and driven units off of the go kart. I took both apart and cleaned them. Both were surprisingly clean and without rust. Inside of the drive unit I discovered one of the roller weights was crooked within its channel. After cleaning and replacing, I put everything back together and tested out the kart. It ran fine for about 10 minutes and then begin to get "stuck in drive" again. I've yet to re-open the TC drive unit again but i expect to find the same issue (crooked roller weight). I'm assuming once something like this happens a couple of times, you're best just getting a whole new unit. I plan to open and inspect the TC drive unit again. I'd i find its the same issue with the crooked roller weight, I'm buying a new TC drive unit.


Sent from my iPhone using Tapatalk
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Update - I figured out how to get both my drive and driven units off of the go kart. I took both apart and cleaned them. Both were surprisingly clean and without rust. Inside of the drive unit I discovered one of the roller weights was crooked within its channel. After cleaning and replacing, I put everything back together and tested out the kart. It ran fine for about 10 minutes and then begin to get "stuck in drive" again. I've yet to re-open the TC drive unit again but i expect to find the same issue (crooked roller weight). I'm assuming once something like this happens a couple of times, you're best just getting a whole new unit. I plan to open and inspect the TC drive unit again. I'd i find its the same issue with the crooked roller weight, I'm buying a new TC drive unit.


Sent from my iPhone using Tapatalk

You do not need to get a new unit. Just buy new roller weights. You will probably find that yours have flat spots on them preventing them from rolling properly
 

mindymogul

Mistress of Destruction
Messages
420
Reaction score
22
Location
Land of Camo and Fireball
You also might wanna consider adjusting your engine placement or finding someway to tighten that chain because in about 5 or so miles on that you're gonna be finding yourself a new one with as much play as it has.
 

MalakyTags

New member
Messages
19
Reaction score
1
Hi LandUse - I could buy new roller weights at $20-$30. Or it could be the springs holding them together, another $20-$30. Or it could be the channels the weights sit in; I noticed off-set grooves where the weight had shifted to ($60+ for a new plate?)I just feel like once I start replacing the torque converter parts I might be better off replacing the whole TC system/drive unit. I saw a blast led drive unit for sale on Amazon $77.99; anyone have experience with this? Do you think the Blast LED drive unit would work with the comet 40 series driven or am I better off trying various new parts on the drive unit instead of replacing?



Mindy - thank you for pointing out the loose chain. We've got that taken care of.


Sent from my iPhone using Tapatalk
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
blast led is some cheap Chinese seller specializing in selling anything from china(especially LED lights?), you are looking at a knock off 40 series drive unit it should work, but keep in mind that instead of spending $150 on genuine you are spending half for something that could have quality and durability issues, just like anything from china.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
blast led is some cheap Chinese seller specializing in selling anything from china(especially LED lights?), you are looking at a knock off 40 series drive unit it should work, but keep in mind that instead of spending $150 on genuine you are spending half for something that could have quality and durability issues, just like anything from china.

That being said....we haven't heard any negative reviews of the Chinese TC's. They seem to hold up OK
 

mindymogul

Mistress of Destruction
Messages
420
Reaction score
22
Location
Land of Camo and Fireball
That being said....we haven't heard any negative reviews of the Chinese TC's. They seem to hold up OK

I have them on my go karts, mini bike, snowblower and log saw. They're actually made REALLY well. Can sure take a beating for $120. I know that much. Though I'd recommend finding a GATES G-Force or Powerlink CVT belts for backup. The China Special ones are crap after 20 or so hours.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
I have them on my go karts, mini bike, snowblower and log saw. They're actually made REALLY well. Can sure take a beating for $120. I know that much. Though I'd recommend finding a GATES G-Force or Powerlink CVT belts for backup. The China Special ones are crap after 20 or so hours.

yeah, we have heard that the Chinese belts suck. I compared a chinese one to a genuine comet and the difference is night and day. The chinese belts are not thick (they are just as wide, same circumference, but the actual belt is thinner, like not just a little bit, maybe 2/3rds to 1/2 as thick).
 

MalakyTags

New member
Messages
19
Reaction score
1
So, I'm heading back to camp this weekend and will have a solid opportunity to once again disassemble the torque converter. I'll get some good pictures of the weights, and the channels they sit in and post when I get back. That should help decide what direction is best to go in.


Sent from my iPhone using Tapatalk
 

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
The kart is moving while idling? Good. Apply the brake when it is started. That is free horsepower that needs to be tamed with the force of a brake.
 
Status
Not open for further replies.
Top