Go kart kit

[RattleSnack]

http://www.northerntool.com/shop/tools/category_go-karts-electric-bikes-scooters+go-karts-atvs

What cheap but good engine can I use with this? And does it necessarily need a clutch?

 

[mwillika]

I'd go with the 212 predator from harbor freight, its on sale at the moment for $120 i believe. And you need a clutch if you want to the engine to be able to be on while the go kart isnt moving, and so you dont stall when you come to a stop

 

[OzFab]

BMI karts have the same kit much cheaper. Having said that, the shipping cost may make up the difference but, it's worth checking out...

Another option for you is to find a beater on craigslist & refurbish it

 

[landuse]

Those azusa kits are very small. Unless you are a kid, you might not fit into it. Just make 100% sure of the dimensions before you buy it

 

[mysteryboy28]

buy a nice used go-kart, ready to ride for $300. take it apart and put it back together a few times. sell it, then build your own.

 

[RattleSnack]

I'd go with the 212 predator from harbor freight, its on sale at the moment for $120 i believe. And you need a clutch if you want to the engine to be able to be on while the go kart isnt moving, and so you dont stall when you come to a stop

Does the clutch come in the engine? Another stupid question. And is the one with EPA &CARB better than just EPA?

Edit: How would you put the clutch in? Any vid links?

 

[souperman000]

The clutch does not come with the engine, you have to put it on yourself. It just slides on the shaft and you put a bolt in the end, tighten any set screws and you are good to go.

The CARB and EPA things are just California emissions laws and regulations. If you have a choice, get one without.

 

[RattleSnack]

I'm 5"5', and the Azusa kit length from seat to pedals is 28 inches, would I fit?

 

[souperman000]

Take some chalk and draw an outline on the driveway that is the same dimensions as the kart frame, especially from seat to pedals. Imagine the kart zooming around, are you comfortable in that position?

People can fit in a lot of things, whether it is comfortable or reasonable for them to do so is another matter.

 

[RattleSnack]

Could I use this engine with the kit?

http://cleveland.craigslist.org/bfs/3932536867.html

 

[RattleSnack]

Also, what's a comfy length of seat back to pedals for someone like me?

 

[souperman000]

Could I use this engine with the kit?

http://cleveland.craigslist.org/bfs/3932536867.html

That engine is an 8hp, so it most likely has a 1 inch shaft. Meaning any clutch or TC will be a lot more expensive than the more widely used 3/4" shaft.

Also, the footprint of that engine is larger than most 6.5 hp or less engines, so the motor mount on that kit will probably be too small without modification. And you will have to remote mount the tank.

Short answer, no.

Also, what's a comfy length of seat back to pedals for someone like me?

Take some chalk and draw an outline on the driveway that is the same dimensions as the kart frame, especially from seat to pedals. Imagine the kart zooming around, are you comfortable in that position?

People can fit in a lot of things, whether it is comfortable or reasonable for them to do so is another matter.

...

 

[OzFab]

That engine is an 8hp, so it most likely has a 1 inch shaft. Meaning any clutch or TC will be a lot more expensive than the more widely used 3/4" shaft.

It's not likely, it's definite, read the ad again...

For the price of that old engine, you can buy a new predator & a clutch...

 

[souperman000]

It's not likely, it's definite, read the ad again...

Yeah...I just looked at the picture. Its the same basic engine I have on my kart.

 

[RattleSnack]

Thanks for all the help guys.

Now, would this clutch ( http://cleveland.craigslist.org/rvs/3935102390.html ) work with the 212 predator engine?

And also, would this ( http://akroncanton.craigslist.org/grd/3845377422.html ) be a good deal?

 

[souperman000]

The ad doesn't say what bore the clutch is. If you ask the seller I'm sure he will answer your question. 3/4" is the size you want.

 

[Russ2251]

A kt100 needs a specific kind of clutch...not just an off the shelf item.
Prices start around $250.
Probably needs a starter as well...$250.

What experience do you have with karts?

 

[RattleSnack]

A kt100 needs a specific kind of clutch...not just an off the shelf item.
Prices start around $250.
Probably needs a starter as well...$250.

What experience do you have with karts?

Literally none...so the predator 212 needs a starter with that?

 

[souperman000]

Literally none...so the predator 212 needs a starter with that?

No the 212 has a pull start. Russ was saying that the kt100 needs a special starter.

 

[RattleSnack]

Ok. Does this look good as well?

http://cleveland.craigslist.org/for/3900630758.html

What happens if a carburetor isn't cleaned out?