Gearing ok?

Status
Not open for further replies.

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
hey guys i would like to know if this is a good gearing cause i cant figure it out. on so its a 12 tooth on the engine, 60 on the primary drive of the jackshaft, a 53 on the other end of the jackshaft for the secondary drive, and a 23 tooth on the wheel which is 20 inches. is this too high or should i leave it
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
unless you got a diesel truck engine hooked up to this thing, no, thats about a 2.17:1 ratio! to figure out a good ratio can you tell me :
what kind of engine are you using? do you have a tc or cent clutch? where will you be riding.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
I'm assuming with 12 on the motor it's #35 chain. Due to it being smaller than #40, you can get a 72 tooth sprocket that is a reasonable size and achieve a 6:1 ratio with out getting a jackshaft. But with 20" tires, you will probably want between 8-10:1 if you are using a cent. clutch. Say 12 on the motor, 36 on the JS in, 12 on the JS out, and 36 on the axle will give you 9:1. This may not be a great top end, but it should keep your clutch from burning up.

EDIT: In theory, the above would yield 24mph.
 

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
well i am sill using the whole bicycle bottom bracket and such. i have that as the jackshaft and i am thinking of putting a 40 tooth onto the wheel so that seems like it woud add a little more torque. so far its 35 chain for the primary and regular bike chain so i think 40 on thesecondary drive
 

bajagokart

New member
Messages
779
Reaction score
0
Location
Red Deer, Alberta, Canada
hey guys i would like to know if this is a good gearing cause i cant figure it out. on so its a 12 tooth on the engine, 60 on the primary drive of the jackshaft, a 53 on the other end of the jackshaft for the secondary drive, and a 23 tooth on the wheel which is 20 inches. is this too high or should i leave it

How big is the rear wheel?

if you read the post, it is 20 inches
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
20" with a cent. clutch is what is making me think higher. Maybe 7:1 but I don't want to smoke your clutch on the first run. What do you weigh?
 

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
Well I weigh 150 and so far the cluch has been holding up but the chain keeps falling of so I've made a few idlers and it won't stop falling off
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
i'm confused, you have a 6.5hp, driving what is basically a bike with 20" wheels, your running a 2.17:1 ratio and the clutch is fine, and according to the speed calculator your going 100mph? please clarify, also to solve your chain problem, either:
install washers if possible to move the engine and sprocket further apart.
remove 2 links of chain
remove 2 links of chain and install a half link
if none of those work try throwing up some pics so we can help design a tensioner.
 

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
haha well i cant do the links because i have removed links until they wont fit no more. and the idlers i have are made out of a skateboard wheele for a tensioner and a rope pully as a guide in a way. the sproket alignement is by eye so its prob not the best. and the clutch is pretty toasty afterwards and i think it might be jumping a few links every now and then....certainly not a 100 haha i hit about 24mph before it fell off. it was an exhilarating 24 cause ive never driven a moto mike. and it was sick. once i finish the tensioner which i have an idea i will be posting pics. i also should be gettin a tav2 30 series soon
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
well it seams as though you have horrible gearing, and the cent clutch is just barley surviving because this is such a light weight vehicle, but because of the crappy gearing the 6.5 can only manage to push you to 24mph, and take 3 yrs to get to that speed. and yes i know he is not going to be going 100mph any time soon.

p.s. i'm not sure a tc on this thing is a wise choice
 

Imbo

Young Mechanical Genius
Messages
263
Reaction score
0
Location
Garden City, NY
hahaha well i just re adjusted my chain tensioners. i almost killed myself cause the bike lifted up and i went off the back...i wheelied and almost freakin died! i will be liwering the gearing soon and it should hopefully let the chain under less stress not slip off. i was goin around 30 so this was pretty intense. tok around 8 secs to get there
 
Status
Not open for further replies.
Top