Exhausts

Status
Not open for further replies.

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Alright guys, what do you recommend. I want my exhaust to be loud but I don't want it to be a high pitched sound. I want it to be a rumble sound. What do you guys have?

Post some pics of your exhaust, i need some new ideas.
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
I used a 3/4 inch pipe then went to a chromed out 2 inch, 1977 chevy pickup exhaust tip lol. Ill post picks in a few min. It sounds pretty sweet
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
What sort of engine do you have? Typically I'll take 3/4" black pipe with 1 bend and run it out a foot and a half, paint the pipe, run once then slice at an angle where the paint has stopped being burnt off totally. Its an old header trick, works great.
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
To make it deeper and louder it has to be a wider exhaust because of soundwaves and echo purposes. So really its just a matter of fabbing somthing up with a large end opening
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
To make it deeper and louder it has to be a wider exhaust because of soundwaves and echo purposes. So really its just a matter of fabbing somthing up with a large end opening

:iagree:
However, you have to find a happy medium between loud/deep enough & "starting to lose back pressure". Without back pressure you will start to lose power &, eventually, burn out exhaust valves
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
it is not nesercery like in 2 strokes

i did read that if the exhaust is far too short or non existant that it is bad for the valves

iv got a cm 250 with the exhausts off a 600cc (just what came with it)
but they are far too wide and have a slow 120* curve to a home made straight though muffler

idles like a big deisel and rumbles when u put your foot down
sounds stupid for a 250 but if thats the noise u want then it works
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
We have discusse back pressure numerous times in the past. The aim of a 4 strokes exhaust is to expell the gases as quickly as possible. There is obviously an art to this, hence why exhaust manufacturers sell some Briggs and Honda exhausts for $80+

If the exhaust is too short or non existent, then it is supposed to be damaging for the valve/s because they will cool down more rapidly, which can potentially crack or warp them.

I would recommend a staged header of some style, also large mufflers can help deepen the sound IIRC.

A straight pipe with no stages etc is really quite loud and harsh, and often produces a loud 'rrrap' sort of sound. Been there. It is fine, but can piss off the neighbours!
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
Ive been their with the neighbors more times than i can count. Lol my quad putsout like 144 decibles. I used about a 14 inch header and it sounded good but loud engines run in the family blood so i added a megaphone type deal it sounds pretty cool. This is for a briggs btw not my quad
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Well i have a glass-pack. I might split that in half and see what I can do. If i'm not able to do that then I'll make like a 6" wide cylinder and mount it to a 1" Pipe, think that'll be nice?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
wait, sorry to kind of change subject but, i thought backpressure on 4 strokes was bad?

Have you ever driven a car with a blown exhaust manifold or flange gasket? There's no power. Why? Because there's no backpressure. It doesn't need a lot, but it needs some to prevent valve damage
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Valves aren't going to get hurt without "back pressure". Do not confuse "back pressure" with "cylinder scavenging".

OP- Search for my Cherry Bomb. I haven't got time to dig up the link right now, gotta buzz off to work, but it's here and I think you'll like it.
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
The pipe on mine is only 2 inches 6 would be cool but make sure the 1 inch pipe is long enough for valve cooldown. The small pipe on mine is 3/4 and it acctuly goes about 1/3 of the way into the chrome pipe. I will explain more later i gotta go to school.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
The pipe on mine is only 2 inches 6 would be cool but make sure the 1 inch pipe is long enough for valve cooldown. The small pipe on mine is 3/4 and it acctuly goes about 1/3 of the way into the chrome pipe. I will explain more later i gotta go to school.

Alright, I'm actually in school right now. I wanted to do my design in turboCAD but it got erased off my laptop when i switched over.
 

Jake.B

New member
Messages
495
Reaction score
0
Location
California-USA
So basicly my 3/4 pipe runst from the exhaust manifold 1/3 of the way into the chrome the overal length of the exhaust system is 14 inches. the 3/4 pipe is probably 8-10 inches and the chrome pipe overal length is about 7 or 8 inches. But the 2 overlap making it acctually about 4-6 inches. Because of the length, weight, an leverage make sure it is bolted on with a flange and not twisted into the head. If it is twisted into the head from heat it will become loose and wobble eventualy tearing up your thread and possibly crack the head. fab up a strap for support. I havent yet as you can see but it needs to be done. Im planing on just bending a strap and run it from a mounting spot on the engine to the end of the exhaust pipe so there is no play and is sturdy.
 
Status
Not open for further replies.
Top