Engine rebuild gone wrong

Status
Not open for further replies.

Number157

New member
Messages
4
Reaction score
0
Location
...
I rebuilt my Predator 212 after a rod failure.

Everything went back together well and the engine started right up, however, I am smoking really bad and literally have oil slowing pooling below my exhaust.

This is the first time I have worked with a piston assembly... do I have an issue with the piston rings or something else?

I know these are inexpensive engines, but I kind of stuck on learning what I did wrong and learn from this lesson.

Thank you for your input...
 

Number157

New member
Messages
4
Reaction score
0
Location
...
None that I can see.

---------- Post added at 05:48 AM ---------- Previous post was at 05:45 AM ----------

ToyCrusher: I did not see any damage.
PoBoy: Unfortunately, I am in So Cal.
 

Number157

New member
Messages
4
Reaction score
0
Location
...
Could the problem be with the orientation on the ring gaps? Also, on this piston there are 4 grooves, but the 2nd grove from the top did not look like it was meant to hold a ring. The piston is configured with the Top Ring in the first groove from the top of the piston, nothing in the second groove from the top, the second ring in the third groove and the thinring+corrugated ring+Thinring in the fourth (wider) groove.

Is this the proper set up?
 

Kokamo

Azzkicker extraordinaire
Messages
33
Reaction score
1
Location
Liberty Hill, Tx
Number157, please fill out your profile. There will be more people willing to help if they know you a little bit better.

From what I understand, and without pictures, I think you have your rings correct. However, if the ring gap spacing is too close, it won't produce clouds of smoke, let alone puddle oil out of the exhaust and I doubt that is your problem. Either you have a broken piston, too much oil in the crankcase, you may have gotten the ring caught sideways upon installation and it's leaking oil (I doubt it because you would have noticed a very tight moving piston)....or you put on an old head gasket that was damaged or even possibly put on the incorrect head gasket.

I ran into this on a brigs OHV motor just this past week on a customer's mower....the thing smoked like Cheech and Chong immediately after startup and only got worse as it warmed up. Eventually oil pouring from the exhaust...I was expecting a ring wear issue from the color of the oil (ink black from improper oil changes) and quoted customer accordingly. Upon removal of the head, I found that the head gasket was blown between the compression ring and the oil drainback hole that goes to the crankcase. So every time it pulled air on a suction stroke, it pulled oil from the crankcase and when it completed the burn, it blew some exhaust into the crankcase and then even more upon pushing the exhaust out thus having tons of blowby and forcing oil into the intake breather.

That being said, I would go ahead, pull it apart and check your rings and gaskets. When you put the rings back in, face the gaps at least 90 degrees from one another.

Edit: upon further thinking, when the rod failed, check the case for any sort of broken parts that could possibly cause this issue.

Good luck and post back findings!

~Joe
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
PoBoy: Unfortunately, I am in So Cal.

Dude Don't encourage them!
Sorry but you are 2 and 1/2 hours from me+ LA traffic, you may as well be in New York.

From AGK http://www.affordablegokarts.com/file-fit-rings.php
"Note: Inspect the rings for any markings near the end gap. Rings are always installed with their markings face up. If there are no markings, it doesn't matter which way they are installed.
The positioning of the end gap on each ring is very important.
When looking at the top of the piston, the end gap of the top ring should be in the 12 o'clock position. The end gap of the second ring should be at the 6 o'clock position. Place the corrugated ring at 12 o'clock, one thin ring at 3 o'clock and the other thin ring at 9 o'clock.
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
why did your rod break in the first place? Dont they break because of over-revving or because of oil starvation?
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Thanks Joe, and as anyone here who knows me also knows I always push for folks to fill out a profile location....but he has posted he is somewhere in southern California...so...right at the moment....it's up to the members close to him...

But...it would be nice if he (and everyone else)...would fill out a profile location!

As I've said over and over...no one has ever said they regretted doing it...but many have benefited and were happy they did!
 

Kokamo

Azzkicker extraordinaire
Messages
33
Reaction score
1
Location
Liberty Hill, Tx
Thanks Poboy. I've owned, admin'd and managed several message boards over the years and it's aggravating to help out a user who is incapable of performing a simple task to help themselves out. Buuuuuut, it is what it is!
 

Number157

New member
Messages
4
Reaction score
0
Location
...
Really, “incapable”?
Do you have a feel for how condescending your banter looks to a new user? I would assume that a primary function of this Forum would be to help someone who is reaching out for advice – instead you chastise them for now filling out their profile before posting?
You gentlemen set a poor tone for new users.
 

Kokamo

Azzkicker extraordinaire
Messages
33
Reaction score
1
Location
Liberty Hill, Tx
Really, “incapable”?
Do you have a feel for how condescending your banter looks to a new user? I would assume that a primary function of this Forum would be to help someone who is reaching out for advice – instead you chastise them for now filling out their profile before posting?
You gentlemen set a poor tone for new users.

Yeah, well, my apologies for being a little blunt. If you lurk on this website enough, you will see what and why it's important. There are so many people spread out all over the country, there just might be one guy that could be the epitome of help just around the corner. It's not only the location, but a name would help make the experience a bit more appealing and personal. The other bits on your profile will tell about your age and mechanical experience. This will let any potential help know who they are dealing with...being a kiddo, or a well versed mechanic who might be stuck in a jam.

Please don't take anything personal, I try to help when I can.

I hope your motor get's fixed up.

~Joe
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
If you lurk on this website enough, you will see what and why it's important.

If you lurk on this website enough, you will see it's suggested but, not mandatory to fill out your profile...

You gentlemen set a poor tone for new users.

Please understand that kokamo's views are not those of the forum in general; although he may have previous experience with online forums, he is also relatively new to this forum...

As for the engine issue, the cause could be one or a combination of many things; unfortunately, repairing the issue will, most likely, involve tearing it down & starting again, making sure everything is in the correct place & alignment; something as simple as the piston being 180° out may be the issue...
 
Status
Not open for further replies.
Top