Engine / Final Drive combo question

Status
Not open for further replies.

Rick20

New member
Messages
3
Reaction score
0
Hey I put this on general forum, but probably should be here?


First post. Hopefully the Kart pic uploaded. OK, here is the question. This Johnson Kart is on my Craiglist. I can buy it for $175 which I think is a good price. It's been very hard but I finally found a pic from J & J that shows what appears to be a Honda GX 2 to 1 reduction engine driving via belt from reduction output shaft directly to axle pulley, nothing else. No jackshaft or secondary chain. I want to do this exact thing, engine to axle. The pic shows a pulley on the axle so I think it was built to do this exact thing. Now, I might be willing to spend the money for the engine, possibly 9 hp. What can I expect for starting, stopping, acceleration and top speed.
 

Attachments

  • cart2.jpg
    cart2.jpg
    63.5 KB · Views: 11

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
We'd need to confirm the axle pulley & rear tire diameters to calculate any potential top speeds, then we could experiment with substituting various engine pulley diameters, plus calculate for a 2:1 reduction engine.


Here's a link to a speed calculator you could experiment with:
http://www.diygokarts.com/speed-calculator.html

(Most all the stock 4-cycle kart engines are governed to rev up to around 3600rpm)

Here's a link to a #35 sprocket diameter chart to help out (converting pulley diameters to # of sprocket teeth) for using that speed calculator:
http://www.azusaeng.com/Sprockets/AzSDno35.pdf

That looks like a pretty darn heavy kart, I'd probably start out setting it up with around a 6:1 overall drive ratio...

__________________

PS:
You could probably save A LOT of money by replacing that axle pulley for a chain sprocket:

Then you buy a conventional kart engine with a centrifugal clutch or torque converter system, instead of having to purchase a way more expensive equivalent engine equipped with an internal wet-clutch and 2:1 gear reduction... :thumbsup:
 

Rick20

New member
Messages
3
Reaction score
0
Thanks for taking the time to help me. I just want a two seater and since I weigh 260 I liked the concession Kart thing because those easily handle me and my grandson at the park. I was trying to mimic that set up. I know in the 70's the direct drive (engine to axle) via centrifugal clutch with chain was ok but the clutch didn't last long.

Are you saying that with the "best" heavy duty centrifugal chain /clutch setup with a engine like a predator, maybe in the 10 HP range, it could pull a Kart like this off the line without crawling and move on up to it's potential speed pretty good without going to the secondary jackshaft setup? Would the clutch give me acceptable wear service?

I am open to going with a much lighter Kart as long as it had double wide seat, just worried about me fitting in it.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
With all that weight, I'm thinking a 420cc engine and a 40 series torque converter would be your best option for good acceleration and top speeds:
http://www.harborfreight.com/13-hp-420cc-ohv-horizontal-shaft-gas-engine-epacarb-69736.html

If you don't want to install a jackshaft, this 40-series TC kit has one that's built right into the side plate, and it would all simply bolt right onto that engine:
http://gokartsusa.com/TC3-40-Series-Torque-Converter-1-Bore-Driver-3/4-Bore-Driven.aspx

And then install a #40 pitch axle sprocket that's around 1-1/2" smaller diameter than your rear tires. Here's a link to a sprocket diameter chart for sprockets that match the pitch of the 10-tooth drive sprocket that comes with that TC kit:
http://www.azusaeng.com/Sprockets/AzSDno40.pdf

Then later on, you'd always have the option of simply replacing that 10-tooth drive sprocket with higher tooth-counts, for more top speed.
 
Status
Not open for further replies.
Top