Engine choices: where to go?

Status
Not open for further replies.

rifkin

New member
Messages
66
Reaction score
0
I picked up a second kart a few days ago. This is a Manco Phoenix Eagle II LXT or something along those lines. It seems to be fit for little people but whatever I have no shame. I am planning on relocating the steering to the middle of the cart, putting in new tie rods and a new seat.

Well that is fine and dandy, you say, but what does this have to do with engines?

Well I have a predator 6.5hp with a straight pipe on my other cart linked through a comet 20 series. This one has a Tecumseh 6hp through a comet 30. Is it worth it buy performance parts for the Tecumseh basically outlined here http://home.roadrunner.com/~pages/kart/kart1.html or would I be better off buying a new predator 212 and putting the Tecumseh away?

Out of left field is the Lifan 125cc 4 speed engine. I stumbled upon them 2 days ago and it opened a whole new world of imagination land for me. I am pretty sure I can fit it on the back of my other kart and move the predator I have to the new car. I don't know if I would want the series 20 or series 30 cvt but I have the option at least.

The even crazier option is to find some broken 2 stroke 125 engine and rig that up but I think that will cost too much money and effort.

I am open to suggestions and ideas. I can probably manage to take photos if need be. The sky is the limit, well until it requires me to weld something. I don't know how to do that yet.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Out of left field is the Lifan 125cc 4 speed engine. I stumbled upon them 2 days ago and it opened a whole new world of imagination land for me. I am pretty sure I can fit it on the back of my other kart and move the predator I have to the new car. I don't know if I would want the series 20 or series 30 cvt but I have the option at least.

I'd be tempted to do this. Now, IIRC, the 30 series has a 10% overdrive and the 20 does not, so I'd probably go with that. I'd also send me the Tecumseh.
:D
 

rifkin

New member
Messages
66
Reaction score
0
I have zero welding and fab skills but I think that for the most part things would line up okay. I would probably have to make some form of new engine mounting plate for the Lifan but I could bolt that to the existing engine mounting plate. That would make lining up the jackshaft pretty easy and the challenges from the back end would be complete.

Up front I would need a clutch and a shifter. I am sure I could find a steering wheel mounted clutch level that would bolt on easy enough so then I am stuck figuring out a shifter. Like I said, I have no fab skills, but this is a little ways down the road at best.

The new kart with the series 30 does feel quicker but not as fast on top end but that might be the smaller tires. I am not sure about top speed too much, I might be able to get out and test it with the gps this afternoon. I had my other kart with the predator before the exhaust into the 20s in my backyard which seemed pretty good to me. In the end if both could be about equal in speed and acceleration for backyard beer league dirt track racing it would be nice and give me an excuse to get a third kart for the lifan project. I will try and green light the lifan concept with my wife as a fall/winter project to give me some time to plan a bit more. In the end I think the karts need wheel to wheel time to see where they stand against each other.
 

rifkin

New member
Messages
66
Reaction score
0
Maine, smack dab in the middle of the woods too, not by the coast where the seafood is cheap lol

edit: I also tested both karts via gps and I ran out of room while they felt like they were just settling down and stretching their legs. The 6.5hp 20 series hit 26.4 and the 6hp 30 series hit 22.7. I don't know the gear ratios of either kart and the 30 series clutch seems to be too close. Center to center it looks like 6 3/4" which is below the shortest distance of 6 15/16 for the shortest series 30 belt on a 6" driven. gokartsupply.com has this below the belt on their chart "Comet Belt #203589A is also known as Manco #5959 - Fits Manco Model 285,286,485,486 & 906" which makes sense because the belt has a 5959 on it and it is a Manco 486 model. It looks incredibly loose however and I can take it off the clutches without any effort. I am not sure if there is any adjustment for tension to tighten things up and I don't know if the belt could be stretched out or something. Time will tell.
 
Last edited:

aidantandy

New member
Messages
58
Reaction score
0
As someone who started a project with a similar level of welding and fab skills (i.e none) and with some similar components. I'd suggest the simplest route. I'd vote for another 212 predator with the existing 30 series.

Either way I'm looking forward to seeing what you come up with. I drove my kart with a 6.5 clone with TAV copy for the first time today and I can't stop grinning. :auto:

As a side note - I live in Australia but I spent 4 of the greatest summers of my life working at a summer camp in rural Maine in the early 2000's. Beautiful spot, well at least at this time of year it was.
 

rifkin

New member
Messages
66
Reaction score
0
It is a tricky decision because I don't have the money for the lifan right now but I could get the predator. I guess there is nothing stopping me from owning both eventually and having spare engines would be a good excuse to get some more karts. Time will tell I guess.

Two of my sisters were over the house yesterday when I got home from work and I had them go out for a spin. The grin a grown up gets from tooling around on a go kart is priceless. Well one sister was grinning. The other crashed into a truck at probably 15mph. Bent the front of the frame (where a bumper would be if it were to have a proper bumper) from 45 degree angle to a 90 degree angle into the tie rods. Still steers find and no other damage appears to have occurred.

Still hit 26.4 mph post crash though and I only have 350-400 feet of flat straight dirt right now to test it out. I need to sneak out onto the road one of these days for a few minutes lol.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Right on! Well, there's nothing wrong with planning toward the future. Maybe keep it simple for now and slowly build the budget/tools/skills/parts until you're ready.

With regards to your previous belt concerns- Comet specs that the center distances be within 1/8" (IIRC) of published measurement for the belt size. You'll probably find that the engine mount holes are slotted to allow adjustment.
 

dmaznic

dmaznic
Messages
46
Reaction score
0
Location
Toronto
yes, check this out:
1. inspiration
2. customization
3. part supply
4. better parts and optimizing/integration
5. budget reality hits
6. practicality reality hits
7. re-thinking design

moral of the story, if you want to complete a project fast, just do what is immediately available not too far from what made you want to do it in the first place. if you're after "planning for the future", you may end up using those good weather days for mad brainstorming in your room

both approaches could still be really fun!!!
 

Attachments

  • untitled.JPG
    untitled.JPG
    28.5 KB · Views: 0
Status
Not open for further replies.
Top