electrolysis on Torque converter?

Status
Not open for further replies.

B man

Tecumseh FTW!
Messages
2,490
Reaction score
3
Location
Oliver springs,Tn
few questions.
is it safe for the TC?

is it safe?(like does it let off fumes or would it hurt the TC to be i too long)

is it effective?(would it clean the surfaces pretty good)

how do you do it?(whats the easiest way to do it)


and would a battery charger be good for this?
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
It is safe for the TC but it does give off pure hydrogen gas which is flammable/explosive. Do it outside. Wait for BigHead to chime in as he's done it a lot with great success. Try using the search as there's a whole thread on it about gas tanks but the concept doesn't change.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
I used 36v and caustic soda in water. A piece of non galvi wire for the annode. Make sure its fully dissasembled.
Rob
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
STEEL. something that you dont care if it rusts.

i am almost done fixing a gas tank off a 1987 briggs generator that was totally rusted on the inside. electrolysis made it new again!

i also used electrolysis on bolts, engine shrouds, etc. and it has always come out great.

use about 3 spoonfuls of baking soda for each gallon of water, thats what i use and it has never failed.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
does the string need to be wire? so the negative is effective?

yeah, the part has to be grounded (torque converter)

just to make sure, you are dissassembling the TC right? not just throwing the driver underwater?
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I just used some wire that i had in a roll in the garage for an anode. You can also use an old coathanger if you have one. It has to be metal obviously.

Have a look at the pics of my attempt at electrolysis in Bluethunders thread http://www.diygokarts.com/vb/showthread.php?t=9832

You can see i just used a piece of wire rolled up as an electrode. You can also see all the waste on it
 

bighead

New member
Messages
4,022
Reaction score
54
Location
Pacific Northwest USA
just do this.

The anode can be any bare steel that you can find. People like use baking pans for the have lots of surface area and eay to scrape off and clean. Just use a rod or long bolt or pipe. Just make sure there is no coating on it. Bare steel.

The sacraficial anode does not have to be fancy like in the pic below. Just get a pipe and stick it in the water. You can even use a coat hanger folded up. Just make sure it not a coat hanger with a coating on it. (MOST HAVE A FUNKY COATING SO I STAY AWAY FROM THEM)

Also note there will be a black oxide finish on the TC when you are done. Coke Cola will take it right off. So dip it in coke then clean real good. After cleaning wire wheel the faces smooth. Take the TC all the way apart.

Also post a pic of this TC. Lets see what your dealing with before you go any further.
 

Attachments

  • electrolysis_setup.jpg
    electrolysis_setup.jpg
    63.3 KB · Views: 8

bighead

New member
Messages
4,022
Reaction score
54
Location
Pacific Northwest USA
You may learn something from these vids I made. The process is the same. As you can see I just used a threaded rod.

No string just solid rod on the + side. Wrap/tie the TC in the chain and hang from wood. Just follow the pic above and you will be fine. You need to change the water and scrape the sacrificial anode clean every day.

If it was me? I would use vise grips and some chain. I would use the vice grips to clamp the chain the the TC. Solid connection this way. Just do not mess up the faces with the vice grips. I use the bucket method all the time and just vice grip the parts to the chain. Let the vice grip soak with the TC. You can also just wrap the part in chain as well. But I find vice grip easy and fast. Specialy with all the nasty crap this makes.

http://www.youtube.com/watch?v=LCpJRI1mNY8

http://www.youtube.com/watch?v=ZmpDtBkpWnU
 
Status
Not open for further replies.
Top