DIY custom air intake.

Status
Not open for further replies.

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I decided I needed a new air filter setup. I didnt like the air box thingy and I didnt want it with just the outside cover off. I wanted all the plastic off.
I have a 6.5 clone engine on my bike and over all it just looks off, with the stock look.
I was going to get one of those K&N type filter and adapters, I cant seem to find one locally, and Im currently a little limited on cash. Like what most of my bike is composed of, found or made parts.

I had a look at a go kart website. http://www.affordablegokarts.com/curved-manifold.php

I thought this was a cool Idea. I decided I am going to build something like this, but I didnt want to move the carb, I have the throttle set up already and dont want to disturb it.
Through out this, I didnt modify any stock parts. I used all existing parts like the air filter gaskets.

I made an adapter for the filter to relocate it in a different position. I dont have a piece rad hose yet I will soon.


This is the carb adapter to accept the rad hose. I made some stand off's for the nuts to clamp on.


This is the filter adapter part. I made it from a 1/4-20 allen bolt, some of my election picket stock (3/16" cf steel rod) and a piece of 1-1/4" pipe (it was 6" long, cut in half, used 3" pieces for both parts)



 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
Now this is just constructive criticism. I like how it looks and it's a cool design, also helps with not having an air filter in your leg and knocking it off like with the k&n air filter and adaptor.but your choke lever is going to fall out sooner or later, and it might be a ***** to get your hand behind it and move the choke butterfly with your hand. I think you should grind down the top and angle, I don't think the choke will close , I think you should grind it down equal with the carb all the way around and make it circular, and also take some sort of epoxy on the post that goes into the choke butterfly so it stays and is held in so it's not going to fall out going down the street
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I will check into the lever falling out, but it does clear by a 1/4" or so and pivots fully.
I think maybe I will take off some of those corners aswell.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
they make choke lever brackets, i remember, i got my k&n filter and adaptor and thought this isnt going to fall out, and i was coming down the street one day, came back from a run and it was just gone, you have to remember a little bit of a pull up and it pops right out, and thats good then it looked like it would just hit the corner and it can be hard dealing with that, and if anything happens, those corners are going to get in your way, if you make it circle with the carb you also reduce the the small bit of weight frolm the metal, id grind it all down to the welds and then grind the welds flat
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Yes, you can buy a clip that will hold it on. Or do what I did- flatten the "cone" on top with a file and drill a 1/8" hole thru it. Then, carefully drill and tap a hole in the boss on the carb that the lever pivots on. Secure the lever to the carb with a suitable screw, washer, and blue loctite.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I can use an existing screw hole with bolt and make a tab to hole the lever down, it was used to secure the air box base to the motor.
I thought about drilling and putting a screw but that small and tricky location I dont want to mess it up.

I bought some right type of nuts for the carb tube, after that I realized that I dont have the filter for the head breather tube. What can I do that is DIY? Is it nessisary, could I do without?
An Idea I had was to use the breather tube with a couple of layers of coffee filter wired on the end, to make a "filtered endcap".

Any Ideas.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Hey guys, its been a while but I finally got my intake done.
It runs kinda weird on the running position for the choke lever, but on the half way point it goes great.
I bought a piece of rad hose at an auto parts shop. They didnt have any straight universal pieces so I bought one with a fairly straight sections and a bend.




 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
looks good, i would have just angled the connector on the engine downward and had it there so you dont have a long tube
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I agree, it might need a different jet. This however is a totally stock engine except for a repainted fan cover. I made the carb adapter straight because I wasnt sure where the hose was going to go after I bought it.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
rich/lean im not too sure, I did get it to run and work though. when I can get out to a better place to ride it Ill check it then if matters.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
You should have seen it when I took it to the bike and car show a little wile ago. I had loaded the bike up in my buddies truck, it had been cool overnight and the dew had settled, I gave a wipe down and look like it was bleeding with all the rust forming.

The judges came around and were doing there grading, when it came to the paint, they said" paint.. there isnt any". I was like, " what are you talking about it was painting itself this morning, some people think of it as red oxide primer, I call it rust".

I might eventually sand it all and clear coat, but im liking the natural look.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Ahh, I believe the rat crowd calls it a "patina".

With regards to the mixture issue, I would think that the uber-long intake tube would cause a rich condition. That said, if running it part choke helps, that suggests it's too lean. Maybe a compound problem. How did it run before the intake mod? Perhaps the carb's fouled up.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Ya there you go, patina, I like that.

oh ya, the motor ran fine with the stock configuration. I just dont like the look of that air box thingy, hence why this mod. This is just proof of concept that it worked. I haven't really decided where it might eventually stay, I didnt want to cut the hose just yet, still mulling over where and how long it might be.
Im going to look for some u or L shape bent hoses, some short pieces and maybe they might work while keeping the look Im after.
 
Status
Not open for further replies.
Top