Clutch talk.

Status
Not open for further replies.

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Hi all.

I'm looking to get this go kart business on the road (see what I did there?!). I think the most sensible thing to do is to collect all essential parts for the build, such as engine, clutch, wheels, axle, sprockets, brakes, etc; and then build a chassis around them.

First things first, I have an engine. It's a 7hp 2 stroke "Campeón" something or other. It's got a shaft which I believe is 16mm or 5/8" (would that make sense, or is it unlikely?). It doesn't have a keyway, it's a screw.

So, I need a centrifugal clutch capable of taking 7hp (166cc), 5/8" shaft without a keyway that screws on somehow.

Does such a clutch exist? If so, please let me know - if not, what do I do?:huh:

Thanks-a-mucho! :thumbsup:

(I understand I'm asking a pretty blunt question, I think it's easier just to ask rather than ask for clues. Any help I can get I strongly appreciate! Thanks again.)
 

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Sure, I'll have to take pics tomorrow. Sadly the PTO (I'm guessing you're referring to the pump attachment this engine had) I had to batter to get off, it was rusted in place. I ended up hammering and drilling to get the darn thing off. It is in bits, the majority of which have been disposed of.

If I need a keyway, and this engine doesn't have one, what do I do? I don't have access a machine capable of giving me a keyway.
:idea2:
 

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
I see. I thought he was referring to a power take off, which can be pump a attachment, which this particular engine had.

My bad. :oops:

OK, I will try and post pics tomorrow, thanks.
 

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Hi guys. Any help would be great, I need to know (this is coming off as really ignorant... ) if it'll be possible to use this engine or not. I plan to get this started very soon, and my dad has an opening up next week he can take me to a hardware store for the parts I need. Those parts depend on this engine being used or not...


Oh, and, today I weighed the engine. It weighs 18kg, or 40lbs. Is that not a huge amount?
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
If I need a keyway, and this engine doesn't have one, what do I do? I don't have access a machine capable of giving me a keyway.

You could pay a machine shop to cut a keyway into your PTO shaft, and also turn it down to a diameter that perfectly fit a clutch.


16mm = 0.63 inches. So if you measured correctly, a 5/8" clutch might not even slide on your PTO shaft without machining the shaft smaller (or the clutches bushing larger) for a proper fit.


I noticed that plastic tray next to your engine with an old round hub in it. Was this hub originally bolted on to your engines PTO shaft?

If so, you might be able to carefully weld this old hub to a centrifugal clutches hub, and then install the clutch with its drive gear mounted inboard towards the engine, and then tighten down a big nut on the end of your PTO to lock it down and hold everything in place.

But with no key, this would only work if your PTO and that hub have a matching tapered fit so the hub could grip the PTO shaft and not spin. Its hard to tell from your pic, but it looks like your PTO might have a slight taper. To find out you could accurately measure with a Caliper, or just start out by seeing if that old hub will slide all the way on the PTO from either direction or just 1 way.

This link has info about a Caliper used for taking measurements like this: http://en.wikipedia.org/wiki/Caliper
 

Krustalien

Battlebot builder!
Messages
109
Reaction score
1
Location
South of Spain.
Hi, thanks for the reply.

Sadly, that small hub was thrown out ages ago, it was well past it. As far as I can tell (it's not obvious to the naked eye), the shaft isn't tapered.

My problem is, I live in Spain, in a small farming town. There is no machining shop near here, no shops that sell small engines, no kart specialists. Ordering from the USA wouldn't be problem if it didn't cost so **** much. Money I just don't have.

So I'm sort of stuck... I've looked around all over the internet (I have so far spent about 5 hours solid searching) and have found not one good result in Spain engines-wise, or in the UK for that matter. Only in the USA.

So, I have been looking at engines in the USA as an option to this, despite the huge costs. My problem is, this engine I have is a 2 stroke, it's a raw powerhouse. I am reluctant to think about 4 strokes as I know they're not as powerful (all be it quieter, cheaper to run, less polluting). But, if I bought and engine of 6.5hp that was a 2 stroke, and one that was a 4 stroke and compared them, 6.5hp is 6.5hp, right? Be it 2 or 4, the power is the same, right? Or not right?

Thanks. I'll keep looking for fixes for this engine, since if it can be fixed it's obviously the most convenient solution. I'll look around town for a nearby machine shop on Monday.

Again, thanks for the reply, much much appreciated.
 
Status
Not open for further replies.
Top