Clutch Set Screw stipped

Status
Not open for further replies.

btroy

New member
Messages
14
Reaction score
0
Location
DFW
Hi guys, my son brought me a go kart to work on, it appears to be an old Manco, Has a 72 tooth rear sprocket and what appears to have been a 12 tooth clutch. Anyway it has set screws holding the clutch on
(well whats left of it). I was able to get 1 of the set screws out but the other one looks like it may have had a drill bit broken off in it( how I found this out is I was going to drill it but thats not working)and the head stripped. There is only a nub to attempt to get ahold of the other set screw.

I was thinking I could take cutoff wheel to it. The screw that is stripped is in the key way so I am thinking this might work.

Anyone had to do this before?

It has a Robin 6.5 with 14.5 x 6 tires
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Hi guys, my son brought me a go kart to work on, it appears to be an old Manco, Has a 72 tooth rear sprocket and what appears to have been a 12 tooth clutch. Anyway it has set screws holding the clutch on
(well whats left of it). I was able to get 1 of the set screws out but the other one looks like it may have had a drill bit broken off in it( how I found this out is I was going to drill it but thats not working)and the head stripped. There is only a nub to attempt to get ahold of the other set screw.

I was thinking I could take cutoff wheel to it. The screw that is stripped is in the key way so I am thinking this might work.

Anyone had to do this before?

It has a Robin 6.5 with 14.5 x 6 tires

I would just take the cutoff wheel to it. Just make sure that you don't cut the output shaft as you are cutting the clutch off
 

btroy

New member
Messages
14
Reaction score
0
Location
DFW
thanks for the conformation, just didn't want to screw it up.

Is the 72 tooth gear ok with a 12 tooth clutch. I guess it will be ok with a 35 chain?

---------- Post added at 08:43 AM ---------- Previous post was at 08:33 AM ----------

Kart I am working on



I'm not sure if it had a T/C or not

Thanks for the help once again
 

btroy

New member
Messages
14
Reaction score
0
Location
DFW
OK thanks for that info.

Are those just nuts on bolts used as spacers? Never seen anythiing like that before. Alittle crazy.

So is this a Manco? Model?
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Yes and yes. The 72 and 12 is a good ratio with your current tires,
It is a Manco and believe it or not the Nuts for spacers was a factory issue! Yep.
 

Joe-405

Enjoying New Projects
Messages
2,673
Reaction score
98
Location
U.S.A.
Had to do that exact thing a few weeks ago actually. Just cut it til your close and it will slide right off.
 

btroy

New member
Messages
14
Reaction score
0
Location
DFW
cool thanks all, that should get me up and going after a carb clean and a few more tweaks.

Y'all have a great weekend!
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
cool thanks all, that should get me up and going after a carb clean and a few more tweaks.

Y'all have a great weekend!

You too....and even though you're on the other side of the planet. (DFW speaking).... if you need anything....Poboy's door is always open....(except to FreeRunner! )
 
Status
Not open for further replies.
Top