clutch problems

Status
Not open for further replies.

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
hi im new to the forum I recently got a 2 seated gokart it have a 14hp predator engine almost brand new engine but im having a big problem I keep burning the belts im thinking about get a reduction gear box with a wet clutch but im not sure if that is the right way to fix it any help b really appreciated
 

Attachments

  • 20150425_200640.jpg
    20150425_200640.jpg
    473.6 KB · Views: 16
  • 20150425_200652.jpg
    20150425_200652.jpg
    371.3 KB · Views: 20
  • 20150425_200706.jpg
    20150425_200706.jpg
    452.7 KB · Views: 13
  • 20150503_183352.jpg
    20150503_183352.jpg
    279.5 KB · Views: 20

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
Odd.. another "Ty Rail" in less than 24h??

Yes,
wrong TC, get a series40;
personally I'd skip that bolt on kit and go with a seperate jackshaft
(more hassle now, less later I assume)
but that's just me.

Oh, another big factor for burning through belts is the gear ratio!
Mind to tell us what's the OD of your rear wheels and what toothcounts your sprockets have?
That way.. just in case the ratio is indeed off, you can get a new sprocket to fix that as a side order :D

'sid
 

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
The sprocket in the axel is 70 theeth n the one on the other end of the tc is 10 theeth the tires r 22-10-8 I'm pretty sure that I have the wrong gear ratio thanks for y'all help
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
22" wheels and 7:1 doesn't sound too bad for me,
considering the engine size and the use of a TC, that should work IMHO.

You sure it's 70Teeth? (that's an unusual number tbh...)

I'd say add three more teeth to the rear sprocket. (get a 73 teeth axle sprocket)
especially since the series40 has a slightly smaller low ratio,

that should put you at the take off torque you have atm.
another two teeth if you want to increase that take off and also reduce the stress on the belt even more (75T axle sprocket)

But the most important part is indeed the series40 TC I'm afraid.

'sid
 

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
I was thinking about use a gear reduction box like this one
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
which one? (no pic ;))

Nevermind, not exactly a good idea IYAM..
the reason is simple:
as a replacement for the TC with their fixed ratio, you'll NOT be happy!
you wouldn't like to go no faster than 18mph with your kart, would you?

And as an addition it's impractical to say the least... wetclutch reductions are almost impossible to use on a TC (and you STILL need a series 40 after all!)
plus you need maybe five more teeth, a 2:1 reduction would 'add' another 70 ("virtual" teeth; ratio wise ;))
so back at 18mph we are

I'm sorry, but you will not get around a Torque Converter with a kart and engine like yours!

'sid
 

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
I'm thinking instead of using that hi dollar tc I will b better getting a 250cc or bigger ATV or dirt bike engine I'm hoping get a engine/transmission that have reverse
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Although that's not a bad idea, be aware that you'll be opening a whole new can of worms in doing so; first, you'd need to either buy or make a suitable mount for the engine, then you will need to build a jackshaft as the chain will need to run back off the engine, not down; then you'd need to fabricate a shifter & clutch mechanism... a whole lot of work & money ahead of you...
 

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
I'm a welder n fabricator by trade I build one seat gokart that I put 125cc 3speed n runs pretty good if I can find a way to post pics I will show y'all my other toy
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Being a fabricator means it shouldn't be too much of an issue then, especially if you've done it before :thumbsup:

See post #9; there's a link to a thread on how to post pics...
 

backwoodsplayer

New member
Messages
7
Reaction score
0
Location
interlachen fl
I got some updates on the go kart I got a 200cc gy6 motor with reverse for a really good price but I need to run a Jack shaft I got 70 teeth on the sprokect that attached to the axel 22x10-8 tires n 16 teeth on the motor what size sprokects should I put on the Jack shaft to have a good take off power n decent top end speed
 
Status
Not open for further replies.
Top