clutch is giving me issues.

Status
Not open for further replies.

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
in April, upon the arrival of my Predator, my neighbor gave me a 14t cent clutch to go along with it. he put a keystock smaller than the slot, and tightened the screw on the clutch, so itd fit in the keyway. i believe the screw and the 1 key sheared. i put another key after that and the kart worked. now that im converting to an axle, i need to remove the clutch from the shaft. the only problem is... IT WONT BUDGE. it will rotate freely when pushed closest to the engine. if you try to slide it off, it stops about 1/8" of the way. ive tried pb blaster and ive tried minor prying with no success. like a db ***, i forgot the drum was removed when i went to start the engine the other day, and the shoes & springs flew off. the springs are shot, and i need someone to tell me how the shoes look. the kart was geared 4.28:1 and was driven for less than 20 hours on that clutch. im no expert on clutches, so im not sure which parts to check. thanks for any help.
 

Attachments

  • 20120807_165441.jpeg
    20120807_165441.jpeg
    629.6 KB · Views: 7
  • 20120807_165640.jpeg
    20120807_165640.jpeg
    553.3 KB · Views: 6
  • 2012-08-07 17.04.30.jpg
    2012-08-07 17.04.30.jpg
    126.8 KB · Views: 9

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
IMO those shoes aren't too bad.
Maybe try a gear puller. They are not too expensive, and are so useful.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
if you can replace the shoes/friction material, would it be more cost effective than replacing the clutch all together? also, now that the springs are pulled, im sure i can find more at the hardware store. will it be nearly impossible to link all 3 shoes together?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Thank the lawd you didn't have your face near it. I had a clutch explode on a snowblower once- it really woke me up!

I bet there's a heck of a burr on the shaft from the key disaster, preventing you from getting the clutch off. You'll need a puller to have any prayer of getting it off. Once it's off, you can assess it's condition, and likely order new springs.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
would removing the crankshaft (i sure hope you guys say no) give me any advantage? i.e. tapping it out with a hammer and something to hold the clutch while i hit? taking the crankshaft out is work that id rather not do, unless of course i cant spare this shaft. dammit. why is it that the clutch will spin freely when pushed in, but refuses to when it's pulled out. would extreme heat do anything?

edit- I just realized.. The crankcase isn't opening without that clutch being removed. Soo either I yank it off, or cut it off. how about a pry bar? I don't want to bend the crank or the clutch housing.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Step away from the prybar!!! That's only going to do damage. You're going to need a good puller.

How close to the end of the crank snout does it get before it binds up?
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Maybe the thickness of the wire that connects your mouse to the computer. Not far at all. If there was more leverage, I'd be fine. I looked up gear pullers, and they cost around $50 and I looked up the price of a new crank for a gx390 (since mine is probably badly damaged anyway) and they were ~ $110. Is that b/c it's genuine vs a clone crank?
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
Well in the 3rd picture in the OP, you can see the clutch as far OUT as it can go. It can go in, and spin very freely on the crank. It's when I pull it, it locks up. There is one more C clip on it, but I don't think this has anything to do with not being able to take it off, because when my neighbor slapped it on, he never messed with those C retaining clips.
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
If it spins freely when it's pushed in then the problem lies at the end of the crank. Do a careful inspection around the crank for burrs or slight "mushrooming" & file it down; It only takes a few thou to bind it up
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
God.. I swear, you fix one thing, and 2 other things break.

Okay- you opened the door to this...

A month ago, the plastic radiator tank on my '93 Subaru work beater split about 45 minutes away from home. I loaded up with water including a couple extra gallon jugs to get me home. I did a neat thing with vise-grips, and had to only pull over once to add water.

Once I got home, I made a patch for the tank with a strip of fibreglass, a bit of 16ga sheet, and a bunch of JB weld. It held for a month. Last Thursday, I was working 90 minutes from home and noticed my temp gauge climbing on lunch break. The patch was letting go. I did another neat thing with some vise grips and some paint stir sticks and drove back to the jobsite. At the end of the day, I refilled the rad and got a couple more gallon jugs for the long ride home. I ordered a new radiator and took my van to work on Friday.

Saturday night, I installed the new rad. I had monday off, so I took my wife for a drive up to Orillia, about an hour from home on the highway- figured it would be a good shakedown to test the cooling system, so off I went with my jugs of water in the trunk.

Just leaving Orillia, my tranny started feeling funny. Mis-shifting and slipping. I pulled over and sprung the hood- only to discover that I'd blown all my tranny fluid all over the road! :censored: One of the rubber tranny fluid cooling lines going to the rad had split. Dang. I cut off the bad section, and clamped it back on. I walked a mile to a gas station and bought a couple quarts of ATF. Walked back, filled the tranny, and drove off...

10 miles up the road, my tranny felt funny. I looked up again, and literally saw a flood of bright new ATF climbing my hood toward the windshield!:worried2: Pulling over, I saw that the same line had split in the middle! :mad2:

Now what? The dang hose was clearly shot. Taking it off the old rad and putting it on the new one was obviously more than it could take. So what do I do for some hose in the middle of nowhere???

The air conditioning system has been dead for the two years I've owned the car- got a wicked leak that I can't fix... So- out comes the knife- I slashed a section of hose out of the A/C's low side and spliced it into the tranny cooling sytem. I dumped in the remaining 3/4 of a quart of ATF and managed to find a gas station a few miles up the road, tranny slipping and all. I bought 2 more quarts of ATF, dumped it in, and drove home. I took the back roads, which was well over an hour of chewing my fingernails, as the A/C hose did NOT fit the fittings as snugly as it should (3/8" hose on 5/16" fittings- believe me, I tightened those hose clamps!!!).

Got home okay- topped the tranny up full, and applied a second clamp to each end of the hose. The car was horrible the whole engine, driveline, and the left side of the body covered in pink he//. I went nuts with the degreaser! This morning, I drove to work very nervously (1 hour drive, stopping twice to open the hood). Seemed okay today, no apparent leaks, and shifting and locking like it should.

On the plus side, the cooling system (remember the radiator?) has been functioning flawlessly!

Sorry 'bout the novel, but I had to share that after your comment!
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
that was hilarious, despite your misfortunes lol. im sure your wife wasnt happy haha. its just funny to picture all of that happening on top of imagining what that truck looks like. and then where i would be at the end of my rope, you come up with a rig that spells the word "improvise". i dont have any stories that compare to that one, but its always frustrating anytime you cant get an engine to start. especially one with a pull rope.

anyway.. later tonight, ill check out the situation in my garage. but in response to the suggestions about the burrs- there is very little visibility of the crankshaft's end point. how am i going to see the burrs? i can just picture a whole bunch of ground up steel between the two pieces >.<
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
If there's any burrs caused by the key mishap, you'won't see them. But do try to file a wee bit of a bevel in the end of the shaft. It may work.
 

Brandon1023

needs an oil change
Messages
422
Reaction score
4
Location
Miami, Florida, Dade County 305
well i can see light at the end of the keyway, giving me a view straight through. i cant see anything too bad. the keyway is actually in tact which i didnt expect. obviously i cant see tiny imperfections which are causing excess friction. i guess Ace Hardware or Home Depot should have a small enough file to shave down the keyway. ill take a little trip to one of the two
 
Status
Not open for further replies.
Top