Cc vs torque converter for drift applications

Status
Not open for further replies.

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
In a drift vehicle (trike, kart) running pvc on the wheels, would there be any reason to pay extra for a torque converter? A cc would be quicker to spin the wheels anyways wouldn't it?
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
As landuse said, the cc will not be quicker to spin the wheels;

while it's true that it doesn't lower the gearing and thus it appears to be quicker at first glance;
it needs more rpms to break the traction (less torque because of the higher initial gear ratio)
and as soon as the traction is lost, the TC will immediately shift into highest gear (for a series 30 that'd be 10% overdrive)
and the wheel will rotate exactly as fast or even faster than with a CC.

Sure, a TC doesn't make much sense for a drift-vehicle at all;
it's a fraction of a second of bonus until you break the traction, and then all the benefits of having a TC will be gone.

So, if your gearing is low enough, and all you want is to drift.. there is no reason to buy a TC IMHO.
it's still the better option, but the difference will be barely noticeable I'd say.

'sid
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
I can tell you, from experience, if using a CC, you must back off the throttle completely to disengage the clutch once you either stop moving or you gain traction for ay reason...
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
Thanks everyone. I'm searching for a fiberglass bodied kart for this project. Something like this here with wheels around 10" and a 3.5 to 5 hp motor.

Then I'll install a 15 hp motor I have laying around waiting for a home. I could be wrong but I feel like having enough horsepower and slick pvc on the wheels, I won't need to be so concerned with exact gearing or the expense of a converter
 

Attachments

  • 00S0S_83oKJKrPJwt_600x450.jpg
    00S0S_83oKJKrPJwt_600x450.jpg
    35.6 KB · Views: 3

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
If the frame you get was made for a 3.5hp engine, then you will have to be very careful about putting 15hp on it. The frame would more than likely twist like a pretzel. You will have to do a lot of reinforcement of the frame. Gussets, crossbeams etc
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
not to mention that most karts like these do fully enclose the engine, and that your 15hp engine is a lot bigger than a 3.5hp engine so it will not fit in easily.
(maybe not at all!)

'sid
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
I'm counting on some bracing and on having to hack up the body to get the motor to physically fit. My (possibly faulty) reasoning is that since it will be doing nothing more than little donuts on flat pavement, no high speeds, no off-road, that the frame shouldn't be subjected to too much stress. :auto::popcorn::rolleyes:
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
You. might be right about some of those things....(they at least make sense to me)....but I'm curious if you already have a clutch....and what size the output shaft on that motor????
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
You. might be right about some of those things....(they at least make sense to me)....but I'm curious if you already have a clutch....and what size the output shaft on that motor????

You had to ask...

No clutch yet, and not sure where I'll end up.

The motor was from a generator so it has a tapered shaft. I started (but haven't finished) destroying the armature in order to use it as an adapter to 1-1/4" straight shaft
 

Toycrusher

New member
Messages
168
Reaction score
0
Location
Deep Deep South Texas
:huh:Man when it rains it pours.
Will that clutch handle 15HP?

The survival of many components will likely hang on the assumption that the pvc wheels will lose traction well before anything is subjected to those 20 lb/ft or so of torque. If that assumption turns out boggus than I'll need to figure a way to write the loss off on my next year's taxes... :eek::horse:
 
Status
Not open for further replies.
Top