carb choice.

Status
Not open for further replies.

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i figure its time to upgrade my carb as i get money. im looking for a mikuni carb with a filter and adaptor for less than 50 $. anyone know where i can get one? for 6.5 hp honda clone
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i want to get it set up PERFECT if i do it. id like to get an adaptor, air filter, 22mm mikuni, and a jet kit to make sure i get the correct
 

the-cyborg

New member
Messages
476
Reaction score
6
Location
Spring, Texas
I highly recommend you go to http://www.nr-racing.com/raceparts.htm
And get their 22 mm Kit with Long Adapter and 22 Jet Kit for Gx200. This kit has everything you need, thought it is a little more expensive than your $60 budget it is complete and I can almost guarantee it will work it will work for you right out of the box.
I've had 100% success with this combo on everything from true Gx200 to predator clones that being said there is no magic jet size each engine is different and altitude, barometric pressure, temperature relative humidity changes from region to region differs and effects operation and tuning.

Also I highly recommend you also order a couple feet of new fuel hose too, you'll probably need it.

** DIY tech tip**
To make your own cables for fitting into the slide carbs, I use an old small crappie fishing weight lead mold and melt down old lead tire weights to make my cable ends.
Instructions:
  • Place cable end into mold.
  • Place lead in an old clean soup can
  • Heat lead until melted
  • Carefully pour small amount of lead into mold with cable
  • Let lead and mold cool
  • Remove cable from mold
  • With a hand file, file lead down until it will fit snugly and flush into the slide.
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
i may go with it. it would be about 119 + shipping. I think im starting a list here, my list concludes:

get torque converter properly set up with comet "replacement" belt

get an exhaust, uni air filter, and a #90 jet

(possibly) remove the governor, if the engine is hitting it after the torque converter is set up correctly

the mikuni kit you suggested ( by that time the governor will be out as carburetor has no use for it, dont want it to come apart)

billet flywheel,rod, 18 pound springs

90 amp flux wire welder

Frame CLEANUP
 

Jcotz

...wasn't there
Messages
374
Reaction score
1
Location
NY
That sounds pretty good, although it might be a good idea to get a few different jets to make sure you get it right.
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Thats what I want to do with my motor.
I would get a flat top piston, and deck the head if you are installing a billet rod.
The 22 mikuni will be ideal. In the UK they are £20 ($30) new genuine on eBay! that's the first time I have found a karting related part cheaper here!

Do you have some sandpaper and a sheet of glass? You may be able to take something off the head like this if you are very patient.
Compression is the holy Grail with these motors.
Be careful though- it is a slippery slope. You will then start looking at a new cam, then rockers and valves, then bigger valves and head, bigger exhast etc...
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Filters $10 on eBay, measure the mountain point and type it in on eBay,
Adapters, make yourself? That's what I would be doing, but I guess it wouldn't flow very well. I would use a lathe, does your school not have one you could use?
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Really? Wow that sucks. I love my school design department. 6 lathes and 3 mills, a mig welder and more.
Probably best buying an adapter then, I think a homemade one would defeat the object of the big carb!
 

kendelrk

redneck engineer
Messages
2,425
Reaction score
9
Location
westland michigan
thats exactley what i was thinking, also quick question. i took my bike down a long street and once my bike stopped accelerating, while looking down at the torque converter i still wasnt in the "overdrive" position, but i got there while it was up on the crate. am i missing somthing?
 
Status
Not open for further replies.
Top