building a muffler?

Status
Not open for further replies.

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
i finnaly got my kart reassembler and want to make a muffler as itv really is too loud

it is a honda cm250

can i drill some holes in a peice of pipe and thread it though a small fire extingisher or is there a smarter more effective method

this pic is the best pic i could find on google to gauge the size
 

Attachments

  • fire.jpg
    fire.jpg
    70.2 KB · Views: 21

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Go for it! A similar method worked out exceptionally well for me!
The way I see it, you've got nothing to lose by taking a whack at it- if you don't get the results you want, try something else.

To make things a wee bit easier for myself, I used a cutting wheel in my angle grinder to cut a bunch of slots in the pipe instead of drilling a million holes. I'd suggest welding it into the canister instead of just sticking it through. One other point- I welded a blank into the very middle of the pipe so the gasses are forced out into the chamber, and then back into the pipe.
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
Since you already have the fire extinguisher, there's a simple way to build a muffler.

Get a piece of pipe the same diameter as your exhaust port or slightly larger. Drill a hole in each end of the extinguisher so you can stick the pipe all the way through.

Figure out the amount of cross sectional area your pipe needs for proper flow. For instance, a 1" pipe has a cross sectional area of .78 inch. (pi x radius squared). A 1/8" hole has a cross sectional area of .012", so it will take 65 holes to make the same area as a 1" pipe. It takes only 28 holes 3/16" in diameter to equal a 1" pipe, but the smaller holes will muffle better. It's probably a good idea to make twice as many holes as you theoretically need, just to make sure you don't have excessive back pressure. You could also use a grinding wheel to cut slots in the pipe. Use the same kind of math to make sure you have enough.

Make a slot in the middle of your pipe so you can insert a disc and weld it in place to block the pipe completely. Then make your calculated number of holes or slots on each side of the middle plug.

Insert the pipe into the can so you have a few inches of unaltered pipe sticking out each end. Weld the joints.
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
Method #2:

Make a hole in one end of your canister to fit your pipe.

Drill enough holes in the pipe to allow flow. Weld a plug into the end of the pipe.

Insert the pipe into the canister far enough so that all the holes are inside the canister. Weld it in place.

Drill a bunch of holes in the other end of the canister. Some of the Briggs mufflers from the 70s were built like this.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
i shot it with a 22 but it had no pressure in it anyway

it was a 2 hour smoke grenane though as all the white crap blew away
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
I'm working on a bike that already has a muffler, but when I do my next project I'm going to build a more creative muffler. Using a cylindrical vessel of some sort, such as a fire extinguisher or a piece of large exhaust pipe from the auto parts store, I'm going to line the inside surface with window screen. Or I'll insert a slightly smaller cylinder that's drilled full of tiny holes.

The inlet will be attached at one end, but not on the end. It will enter the canister at a tangent. Imagine a can of beans standing on a table. A pipe is lying on the table, pointing at one edge of the circle. That's how the inlet is attached. This will cause the gases to swirl through the muffler.

The outlet is in the center at the other end. It will be either a simple piece of pipe or a pipe that goes in the canister several inches and has the end plugged and the sides full of holes or slots.

Between the spiraling and the flowing over a perforated surface or a screen, it should be super quiet without much back pressure. The outlet can be turned downward to make it even better.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
wait u say widow sreen like off a car

the mitzi colt that im taking parts off is the limited edition

it comes standard with limited head for the driver and passenger acheived by dropping it upside down

can i salvege bits of front window and insert that
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
No- Window screen as in fine metal or fibreglass mesh that keeps the bugs from flying into your open bedroom window and biting your junk whilst you sleep...
 

robbie

New member
Messages
857
Reaction score
9
Location
Osceola, Missouri
If you're going to put a pipe through the fire extinguisher (like the one in Toystory's avatar) you may be able to put a screen (or fly wire) inside. Try rolling it into a tube, then put it inside, and open it up with a long screwdriver or dowels. I'd be interested to hear how this effort turns out. It wouldn't have to go all the way to the edges of the canister to be effective, I think.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
ok im done

first i drilled a set of holes in the top and cold cliseled the gaps between them the get a hole

then i found some galv pipe and drilled alot of holes in it but i had to use a hand held drill (this cost me a drill bit:()



then i welded a plug over the end of the pipe and put it in the fire extiguisher





then i cut anoughter hole in the other end and put an exit pipe in

then i welded both halves back together and made the exhust pipe

this is my new slightly extented staight pipe :ack2:




iv got a little bit more to do
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
If you're going to put a pipe through the fire extinguisher (like the one in Toystory's avatar)

For what it's worth, I didn't use a fire extinguisher. It's a large CO2 cylinder. I point this out only because the cylinder walls were much thicker and it made for a deeper tone. The shape was also closer to what I wanted. The principal is the same, though.

http://www.diygokarts.com/vb/showthread.php?t=7449
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
well iv finished the whole systwm and the report is
IT MAKES NO DIFFERANCE :roflol:

but i dont care as it sounds awsome and now it has more than just the header pipes in is proberly better for it

also it has less chance of throwing a spark and starting a huge fire :ack2:

it has enough back peassure to say running now
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
the only fly wire i could find was plastic

i could cut up our securaty fly screen door but the parents might disagree

also i wouldntrecomend a fire extiguisher as it is like trying to weld a coke can
u really need a tig to do it

out of intrest toy story
can u get decomisioned cylenders and extiguishers?
 
Status
Not open for further replies.
Top