Belt Burns

Status
Not open for further replies.

cwisler

New member
Messages
3
Reaction score
0
Hey guys, just bought 2 go karts the other day for pretty cheap. Both run (need a new carb and can't find one).

Anyway, had the one running yesterday and had to move the little screw on the carb to give it quite a bit of idle throttle. It's got a tendency to take off when it starts up unless someone has the brake held down. If I move the screw out a little, it won't start at all unless the choke is in, but as soon as you get off the throttle when the choke is off, it dies.

Well with the idle throttle so high, the belt likes to burn when it's sitting still. I cleaned the carb out fairly well when I had both of them off. Is there something I'm missing that the throttle needs to be so high to idle? And is there a way to remedy the belt burning situation if the high idle isn't the cause?

http://i50.tinypic.com/2gtntc0.jpg
http://i48.tinypic.com/30nirdv.jpg
http://i45.tinypic.com/2gwb2ur.jpg
 
Last edited:

cwisler

New member
Messages
3
Reaction score
0
I assume the driver is the "gear" closer to the rear? The belt burns on the metallic gear when idling. Belt sits still while the metallic wheel spins -- so the sides of the belt begin to smoke out. Thought part of it could be that it wasn't the proper belt, but I don't want to go out and buy a new belt just to smoke it off if that's not the issue. :)
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Woah- I just had a look at the other pictures. Something isn't right. Get the code from the belt and measure the width on the top. You have either a nackered belt, wrong belt, or damaged driven unit.

Just for clarification- the driver is the pulley/clutch on the engine, and the driven is the one closer to the back.

Also any markings on the pulleys would be useful along with a video.
 

cwisler

New member
Messages
3
Reaction score
0
I noticed when taking the video, that the driver squeezes the belt during idle. I assume that's probably from the idle throttle set too high? The carb may be bad on this one as well, but it cleaned up real nice, no idea what the jets look like, though. I don't remember the belt smoking when I had it idling with choke halfway, but the idle throttle setting was set tremendously lower. When disengaging the choke altogether, it would stall out unless the driver was on the gas.

Belt numbers and width:
http://i49.tinypic.com/k3wqvq.jpg

Video:
http://youtu.be/-z5FXZOba3c

Not sure what you meant by markings, so I took pictures of both the driver and driven, and also took a picture where the belt rubs in the driver.
Driven:
http://i47.tinypic.com/5kiko0.jpg

Driver:
http://i48.tinypic.com/255rnec.jpg

Belt rub in driver:
http://i47.tinypic.com/35ic4rk.jpg
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
That belt is worn. It should measure 3/4" across the top (or 6/8"). Yours measures 5/8".
You can get a replacement here. Check the centre distance between the two pullies is 6-15/16" to 7" because that is what that belt is meant for.

Your belt should not rub like that (obviously). However for some reason I cannot view the video (I think it is my terrible internet connection at the moment.)
I reccomend dissasembling and cleaning both pullies, replacing any worn parts, and getting a new belt. Your idle may be too high as well.
http://diygokarts.com/vb/showthread.php?t=7332
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Problem #1 is the too-high idle. If the engine refuses to idle at a low-enough setting, you have a carb (likely) issue. The idle circuit might need cleaning.
 
Status
Not open for further replies.
Top