Anyone using a 16hp vanguard? Exhaust question

Status
Not open for further replies.

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Hi, I have a 16hp Briggs and Stratton vanguard I'm going to mod into my mini monster. Problem is the stock exhaust will face butt up against the battery box. I'd like to get something with better sound anyway. What do you guys do for exhaust? Is there a tuned length like a 2 stroke? How do I figure that length? I've never done any mods to a 4 stroke so I could really use some advice. 16hp will be plenty for what I need, I just need to relocate it so might as well make it sound cool while I'm there. Thoughts/opinions are appreciated.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
There are some creative exhausts around here, including my Cherry Bomb- perhaps you can get some inspiration from them. 4 strokes are a lot less sensitive to exhaust "tuning" than 2 strokes. Just remember that for the most part, restrictions are harmful to performance and "back pressure" (per se) is unwanted and certainly not needed. Keep the pipes as large as or larger than the port area, and keep length and bends to a reasonable minimum. I have heard tell of a "magic length" for straight pipes, but I would suggest you'd only notice the difference behind the decimal point on a dyno.
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Thanks guys. Seems simple enough if I follow the instructions in that link. Do both pipes need to be exactly the same lenth? Sounds like I'll be doing the bend at the flange and angling the pipe down and toward the back. Should only need the 1 bend in each pipe. I also noticed in the thread talk of a 2 stroke expansion chamber not being necessary. Maybe not necessary but the engine will never get into the power band without. Very inefficient. If you've heard the phrase "get up on the pipe" that's where the engine is most efficient.(in the power band) The shape of the expansion chamber forces the unburned fuel charge from the exhaust back into the cylinder just before combustion. The full length of the exhaust, silencer included will dictate what RPM its most efficient. Back in the olden days bike racers put a long straight pipe on and would saw a little off at a time till it ran best at the RPM they were after. Shorter pipe=higher RPM. Very crude but it's all they knew at the time.
 

brandongeiger2

New member
Messages
584
Reaction score
0
Location
Valrico Florida
Yes make them identical or make a collector and connect them because it will cause unequal pressure if one is different...I forgot most Vangaurd's are twins...
Your right about the two stroke exhaust too (Who am I to tell you haha) thats why you see drag banshees with twin expansion chambers and no silencer, unlike the 4 stroke quads that just run a straight pipe out the back.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
For the size and type of engine, I believe it's not at all critical to have both pipes the same length. The difference would be completely negligible at best. More important is to minimoze restrictions.
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Thanks guys, I'll try to make them as close as possible to the same length but know I can cheat a little. Where do you guys buy your common parts like exhaust, chain, and other stuff? Is there pre bent pieces of exhaust tubing available? I can get it welded together but the bends add another issue. Thanks for quick responses.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
That's pretty cool! As I don't own a bender, I look for alternate solutions, too. One such solution is 1" EMT (Electrical conduit) from your local Home Depot, Lowe's, or other big-box hardware store. You can get straight lengths as well as pre-bent 90*'s. You will have to make your own flanges by copying them from your existing muffler, OR just cut the flanges off your muffler and re-use.

Just beware that EMT is galvanized- use forced ventilation (fan) when welding, and preferably outside. Burning zinc is deadly.
 

brandongeiger2

New member
Messages
584
Reaction score
0
Location
Valrico Florida
I made a straight pipe for my pressure washer by cutting the flange from another muffler haha it's kinda hard to weld though depending on thickness
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
Got my clutches in the mail today. Ran into the next problem. The crank shaft seems to be too short for the primary clutch. Does anyone have a comet 40 series on there 16hp vanguard? Could I see a picture? I was really hoping for a bolt up on the clutches. I knew I'd have to move the engine mount for belt alignment. Wasn't expecting this. I sure hope I can find a way to make this work. It pushes on and touches the engine cases. Even then the crankshaft is recessed inside of the primary clutch. Really wondering what I'm doing wrong. After the Odyssey I thought this go kart was gonna be a piece of cake. Might be turning into a real project.
 

brandongeiger2

New member
Messages
584
Reaction score
0
Location
Valrico Florida
I'm confused on what your saying? Are you using a comet TAV plate or a jackshaft mounted remotely? Also If the crank has internal threads just slide in the key and torque down a bolt after sliding the driver on.
When I had a TQ on my Clone Engine the driver clutch was longer than the exposed crank and I just threaded in a bolt to tighten the TQ down. Just make sure there's a bushing or something to only put pressure on the inner ring of the crank bearing so it doesn't scrub on another surface...


EDIT: That was a 5 line run on sentence haha...
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
It's this set up right here. Clutch and secondary. So I can make a bushing and longer bolt to add length to the crankshaft? It's just a primary clutch, secondary clutch, and a belt. Very similar to a smowmobile/odyssey setup. It's a remote jackshaft setup. Primary on engine, secondary on jackshaft with small sprocket, down to large sprocket at drive wheel.

http://bit.ly/MBO82L

http://www.pilotodyssey.com/PO/viewtopic.php?f=2&t=10587
 
Last edited:

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
It looks like I'll have to add a second jackshaft to make the secondary work. It would add move moving parts but I will get control over where the secondary is located. If there's room for all of this.:surrender:
 

brandongeiger2

New member
Messages
584
Reaction score
0
Location
Valrico Florida
Well I wouldn't make a bushing unless you have a lathe haha the bushing I had was only a quarter inch wide and slid onto the crankshaft, it was just long enough to keep the driver from rubbing on anything. I wouldn't worry about the bushing if the driver clears the engine without spacing because its best to have it closest to the engine as possible.

Now as far as the driven clutch Why can't you just move it to align it it's on a keyed axle, correct? If you could replace the axle with a longer one and use collars to keep it in place you could move it virtually anywhere for alignment. If that makes any sense I'm still sorta hazy on what the problem is haha

PS: Instead of multi-posting just edit the first post :thumbsup:
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
I broke into this project saturday. I got the engine mounted where it's gonna stay and went to work. I'll be making a spacer just long enough to keep the primary from hitting the engine case. That'll work fine. The secondary is mounted on a short jackshaft. The axle setup is weird. It's a 1 tire fryer. The chain goes off the jackshaft to the short axle right by the drive wheel. It only turns the one tire. What I found is I'll need a 1" longer jackshaft and I'll have to move the jackshaft assembly back 8-9" for the belt to be right. Now that I'm doing it it's coming together. Just had to get my hands dirty.
 

spyder1968

New member
Messages
285
Reaction score
1
Location
New Bedford, MA
16hp on a "one wheel peel" ? WOW ! you may want to seriously consider converting that bad boy to a live axle. you are going to turn tires ( only one at a time) into slicks FAST !
 

FatCat

2 stroke Addict!
Messages
459
Reaction score
3
Location
Ottawa, IL
It is live axle. I apologize. I must have been thinking of something else I looked at. Got everything setup and tacked in. Need to take to a good welder to have them complete the job. Looks like it will work good. The shaft I ordered was the perfect length. I need to add a threaded hole to both sides. I will also add braces to strengthen the frame.
 
Status
Not open for further replies.
Top