Any specific tuning methods for piston port 2 strokes?

Status
Not open for further replies.

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
Hey guys, I felt like doing something with a 1960's Victa I found on the side of the road. So I started cleaning it and dismantling it, but I got side tracked and found myself porting the intake :D

I was wondering what are the best things to do to it considering most tuning guides are for reed valve engines, I wasnt entirely sure if I should treat it as one minus the reed part?

I dont think it was treated well as a mower, when I took the bowl off the carb it was filled with a calcium deposit I'm guessing, looked a bit like sand? But I'm hooked now and already scrounging up my spare parts from newer engines to make it more powerful :thumbsup:
 

sexyvicta

New member
Messages
806
Reaction score
2
get 'twostroke tuners handbook.' by Gordon Jennings. Its pretty much 100% talks about piston port engines the same as the victa.

edit: on my friends victa engine on that bike i showed you a pic of, they rasied the barrel a little bit with a spacer and milled a bit of meat off the head. Also has a megaphone exhaust and one of those chinese 125 pit bike carbs. I belive they drilled the jet out on that from .8 to 1mm. It seems to go ok but victas arn't realy rev monsters. Buckets of torque tho.

Im not sure you could do alot with the victa intake without cutting off the existing flange/pipe.

maybe start buy widening the ports a little and maybe raise the barrel? you can always trim the piston skirt to alter port timing aswel...would be cool to add a 5th/boost port

editedit: oh yeh and maybe the best way to go faster would be to get rid of the rev limit(its something like 5-6k-rpm). i think replace the condesor with an automotive unit or ditch the points altogether and run an atom module
 

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
Yea, I will try and find that book, theres one thats floating around on the internet but it might be the one written by someone Bell or something haha.

I'm actually happy with the rev limit because I've seen it mentioned heaps of times that the conrod can fail above 6k and I don't have a press to replace it with so don't want to push my luck.

What advantage does it give them by adding a spacer and milling the head? Wouldn't they cancel each other out somewhat? And I've got some stuff floating around to make a megaphone which will probably end up on my kart engine anyway.

Speaking of the kart engine, I'm doing up that older one to see how far I can go on the other. Its already got the intake tube cut off it so I could mount a briggs carb, that should make it even easier to make it bigger. Is there any advantage to making the exhaust any larger or polished?
 

sexyvicta

New member
Messages
806
Reaction score
2
Y
What advantage does it give them by adding a spacer and milling the head? Wouldn't they cancel each other out somewhat? And I've got some stuff floating around to make a megaphone which will probably end up on my kart engine anyway.

yeh i dont think i would want to rev a stock victa above 6k either:arf:

when you raise the barrel, you raise the ports(all of them), but you also raise the head so skiming it down to keep the combustion chamber about the same size/compression etc.

You're guna have to do some maths here before you go cutting stuff i think. Slightly widening the ports would give you a little more flow without changing the port timing but yeh i have no idea what would work, howver there must be room for improvement as the thing is designed to mow lawns and make power at 2000-3000rpm-ish. You will have to read lots and then measure up the victa and decide what to do
 

jman231994

New member
Messages
724
Reaction score
3
Location
Australia
Genius, thats a great way of moving the ports hahaha

Yea, I'm not really aiming too high with the intake porting cause it's too hard to get at with the angle of it and everything. If only the transfer ports had covers like the 125's then some real tuning would be easy. Widening it really is only possible for the exhaust unless I modded the barrel quite extensively. I might do that one day if I get a spare barrel or a junk engine.

Imagine what the founder of victa would think of his engines now lol
 
Status
Not open for further replies.
Top