Another Blown Predator 212

Status
Not open for further replies.

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
Picked up another "Blown Up" Predator engine the other day off of Craigslist off of a mini dragster. After adding up all the extra parts this guy had over $500.00 in aftermarket parts in the motor. He could not tell me what was wrong with engine and was done with it. He already had another Predator 212 built an mounted on dragster for his daughter (think he is a bolt on type of guy). Anyway got the engine home and started to look the engine over. Below is what I found:

crank.jpg
 

KartFab

Active member
Messages
3,381
Reaction score
60
Location
Dallas, TX
Maybe he forgot to lap the flywheel to the crank and torque it to 65 ft pounds?

Just judging from the pic you know that the flywheel spun on the crank., If you put the flywheel on the right way, you don't even need the key because the friction between the flywheel and the crank is so great that it wont budge at all.
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
That's what I am going to try to get it running but what he was running was the standard flywheel and the cam is the Black Mamba which would turn engine 8000+ and the flywheel is cracked along with the coil plate is missing. I think we found the limit for the standard flywheel (the hard way). His loss my gain I only paid $100. This thing is sick, the decking is 0, oversize piston, GX160 head ported and polished and machined down 0.05. I have no idea how much HP it will have or what the compression ratio is but it has to be HIGH.
 

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
After adding up all the extra parts this guy had over $500.00 in aftermarket parts in the motor. He could not tell me what was wrong with engine and was done with i

We all know that's not hard to do!
Sounds like a bunch of good parts if nothing else.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
8000+ and it didn't "grenade" that kinda looks like the crank failed. Can you post a pic of the crack in the flywheel?

EDIT: WAIT! WHAT? The coil plate is missing? So...the coil comes loose and the flywheel goes from 8000 to zero....yeah...I would expect to see what I am.
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
Threw out flywheel, had to make room on workbench and shed for tear down. Had a run for scrap metal so threw it in ($12.25) for the complete load. Man scrap metal cost have gone down.

Anyway crack was at keyway and out about half way to the full diameter. No grenading, haven not seen one do that and don't want to.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Well...that's why I asked for a pic..exactly where I expected it to be cracked
That's where the catastrophic failure occurred...(kinda) .

My money is still on the coil. Does the engine turn over?

BTW: Thanks so much for this thread...this speaks volumes to the integrity of the stock flywheels and should be a sticky to direct all those people that say: I know I need a billet flywheel if I remove the governor."
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
Engine turns over and all looks good. Will take some readings tomorrow along with run out on crank even though I will replace. The old Predator the plate was mounted to flywheel with a screw and adhesive. New ones (non Hemi at least) is only attached with adhesive.
 

minibiker

New member
Messages
148
Reaction score
1
Location
USA
Don't forget new connecting rod bearings and make sure its to arc spec when done with plasti gauge
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
It was advertised as a "Blown Up" engine meaning a catastrophic failure but yea I got it now. On that topic would love to put one of those Roots Smog Pumps (used as a supercharger) on this one or maybe that would put it over the top. Does anyone know just how far you can push the upgrades and what maximum HP you can get.
 

DeathMachine

New member
Messages
358
Reaction score
10
Location
Eastpointe MI
I do know someone who put a turbocharger on a 16HP Tecumseh, but all it did was blow the fuel out of the float bowl through the overflow tube.

I'm sure there is a way to do it so it works, though.
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
Yea it opens up all kind of issues and probably some that everyone would miss and for the additional power would not be worth the time. If I ever win the lottery or find my long lost RICK uncle maybe I will try it.
 

Grape Ape

New member
Messages
111
Reaction score
1
Location
Virginia
Just found the a compression ratio chart and am wondering if this is correct, the engine I picked up ($100) is as below:
Deck Height 0.000
Head Gasket Thickness 0.010
Old Style 160 Head Milled 0.050
Original Compression Ratio 8.5:1
Per Chart new Compression Ratio 18.7:1
Can this even be ran with 93 octane gas

View attachment Predator Compression Ratio.pdf
 

DeathMachine

New member
Messages
358
Reaction score
10
Location
Eastpointe MI
I can't see milling .050 raising the compression ratio 10 points. My guess is it goes from 8.5:1 to 8.7:1.

Could you imagine pull starting an 18.7:1 engine?
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,887
Location
Chicago-town USA
According to my research....

Milling the 212 hemi Head 0.037" to get 18cc..
Using a 0.027" Gasket
Using a longer rod to get Piston to 0.004" in the hole.

I think I am at 11:1 CR

Milling the 14cc head 0.050" might make the chamber tiny.
 
Status
Not open for further replies.
Top