Alternater

Status
Not open for further replies.

REDNECK GOCARTS

New member
Messages
43
Reaction score
0
Location
Racine WI
I have a 250cc Briggs and Stratton snow blower engine that has electric start. It does not have a alternate on it or any other charging system on it that I know of. The starter motor is rated for 120 volts witch is house hold voltage but first I need a alternate before a starter. How can I add a alternater. What I was thinking was having a sprocket on the output shaft of the engine with a chain running to a jackshaft which would have the clutch on it and a pulley. The chain from the clutch would run to my sprocket on my axle. Then I would use a lawnmower alternater and have a belt between the pulley and alternater. Does that sound legit at all? It would be nice to be able to have a charging system on it. Thanks for reading, Redneck.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Itll work, but it will rob alot of power used by the motor to move the machine it being powered from.
Alternators are a viable choice on more powerfull motors.
The starter is 120v, cause its used at the house or place where ac power is available, and an alternative of it having a battery.
 

REDNECK GOCARTS

New member
Messages
43
Reaction score
0
Location
Racine WI
Could I gear it so it would not rob so much power. All it would be doing is just keeping the battery toped off so I could start it (yes I know I would need a new starter) and keep the lights bright. All I am using for lights are LEDs. Also could the chain from the engine going to the jack shaft wear down quicker because it is constantly moving?
 

qtband

Well-known member
Messages
1,772
Reaction score
72
Location
St. Louis, MO
Is there a smaller alternator that you can use? Maybe you won't need much to do what you need.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
I could see a starter/generator working better in this situation...
Needs all the regulator and stuff for charging...
 

REDNECK GOCARTS

New member
Messages
43
Reaction score
0
Location
Racine WI
I take it that a starter/generator is a starter and an alternater? If that is what it is, then I would not need a new starter, I can get one of those.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
No not an alt, but similar.
Alts typically need a battery to generate a field to generate more power to charge and run stuff...
The geny just needs to spin at a certain rpm to generate an amount of useable power, but need a voltage regulator ect...
A gas golf cart has similar setup... But they are typically a big block or much more powered motor.
 

REDNECK GOCARTS

New member
Messages
43
Reaction score
0
Location
Racine WI
Ok, now I understand. So it would start the engine and charge the battery but I would have to get a regulator and what else would I need? Also, can you get them with sprockets or is it made for a belt and pulley.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Off I can't remember... Pulleys most I think, But look them up...
Like I said some golf karts have this kinda setup.
 

Whitetrashrocker

Inmate #952016
Messages
5,235
Reaction score
4,731
Location
Southern New Mexico
My gen1 Yamaha cart has a set up like that. Gas pedal uses battery power to spin starter. It's belt driven and as soon as the 2stroke lights up it overpowers the starter and it starts acting like a generator supplying 12v which charges the battery.
Sorry I don't know much more. I turn the key on it and go.
 
Last edited:

REDNECK GOCARTS

New member
Messages
43
Reaction score
0
Location
Racine WI
Does anyone know what kinda gearing I would need for the starter/generator. Also, to be able to get close to the same performance and speed, would I need to use the same number of teeth that is on the clutch for my sprockets on the engine and jackshaft?
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Like I said... You need to look up the golf carts...
I don't have time to or I would have...

I reckon it's about 2:1- 3.5:1 but it's belt size ratio...
 
Status
Not open for further replies.
Top