A different way to adjust timing

Status
Not open for further replies.

Thunderbird SC

New member
Messages
51
Reaction score
1
Location
Western New York
Since I'm working on Tecumseh two strokes i cant just use offset keys. They use a one piece collar/key that orients the flywheel 180 degrees and uses two key slot areas to do so. Odd indeed. also keeps one from putting non 2stoke flywheel on i guess.

So i looked into moving the magneto to advance or retard. well seems they have the holes drilled offcenter on the mag's arms already no leaving much room to work with.. Well my welding skills fixed that. Built up the sides a bit, then drilled a large 3/8 then 7/16 hole where the stock no adjustable holes were.

A problem showed up when the holes were larger than the bolts holding the mag down, so either washer or add material back. I opted to add material with my welder carefully to make long slots that allowed me to move the mag 7/16 inch advace or retard. cleaned and flattened all my surfaces, bolted it back on with max advance. Fired it up and yeah, more crackle on the mid to low rpm, same scream wide open. The exhaust is about a foot of 3/4 tube with a few mandrel bends in it. Its currently still on a snowblower and in the summer will go as an additional engine option to my gas powered powerwheels.

Since my timing is rather limited i was thinking about using a few keyway collars to experiment with. File on side of the keyway down and weld some to the other side clean and shape to move it some there. Then maybe in combo with the mag movement I can dial the right level of advance..
 

Thunderbird SC

New member
Messages
51
Reaction score
1
Location
Western New York
Ok got some pics here to share, let me know what u think
 

Attachments

  • DSC02594.jpg
    DSC02594.jpg
    50.1 KB · Views: 15
  • DSC02579.jpg
    DSC02579.jpg
    105.8 KB · Views: 18
  • DSC02581.jpg
    DSC02581.jpg
    57.9 KB · Views: 17
  • DSC02589.jpg
    DSC02589.jpg
    37.5 KB · Views: 14
  • DSC02587.jpg
    DSC02587.jpg
    43.2 KB · Views: 12
  • DSC02582.jpg
    DSC02582.jpg
    65.5 KB · Views: 13

Thunderbird SC

New member
Messages
51
Reaction score
1
Location
Western New York
Well got the engine finished. Tore apart a few others to get the best of the best parts together. Found one had points and a rotatable mount to further adjust timing. Near new piston and rings. Closed the decompression passages (much more difficult to turn over) and some gentle porting. Removed the headgaskets per Russ's sticky too.
Pretty pleased with two engines i currently have, a larger 98cc with dual transfer ports and a smaller 75-80cc with quad transfer ports. Both are currently piston ported intake but should be able to adapt the bottom crankcase cover plate into a reed cage and use the piston port as a vacuum port for a fuel pump.
Speaking of fuel pumps i will definitely need one now as I have reached the limit for the current carbs. Under a full load the fuel bowl will empty and cause the engine to run slower and leaner as it tries to refill the fuel bowl. So yeah, single output snowmobile fuel pump needed. Another performance adder would be a tuned expansion chamber pipe.
Not sure what my current HP is but the hp ratings seem to vary a bit from brand to brand even though they use the same engine size.. the 98cc is a 3hp:confused:
 

Thunderbird SC

New member
Messages
51
Reaction score
1
Location
Western New York
a new rpm limit of 9000 was reached today with the modified 98cc and advanced timing. still suffer from high speed fuel starvation so its not sustained long.
managed to turn the cleaned up exhaust pipe blue a good foot after the exhaust port :D I'd like to see u 4 strokers do that.
thinking up some way to adjust the timing without pulling the flywheel each time, something where i can adjust it from the backside of the flywheel /cover plate. probably some angled fine thread bolt that would push or pull on the timing ring. or just buy the adjustable curve single cylinder msd ignition:wai:
 

Attachments

  • DSCF8987.jpg
    DSCF8987.jpg
    75.8 KB · Views: 9

Thunderbird SC

New member
Messages
51
Reaction score
1
Location
Western New York
yep working on the frame more, needs brakes, throttle hooked up, self welded fuel tank, basic wiring, buy a nice set of 13.5x6 tires and a few other small things to get it running at least. Then add headlights, remote kill and brake option, expansion pipe, mechanical tach and spedo, under glows, and what ever else would add to it.
 
Status
Not open for further replies.
Top