8 horse briggs!!

Status
Not open for further replies.

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Ya, they get hot. Like water. Water gets hot too. Water, now that's something no teen should be exposed to.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
That's it. No air til you have reached 18 and are a legal adult. Girls, no hair straighteners or blow dryers. All of us under 18 no grinders, torches, welders, lathes, saws, motors, drills, etc. because they produce heat and so do microwaves and the state of Massachusetts has deemed microwaves dangerous for teens to operate.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
yeah the town here make laws but cops just sit in their cars and eat doughnuts. once i took my home made pit bike for a 6 mile ride across town to my old elementary school and back. i was red lining the engine all the way on the middle yellow lines, and a cop just drives past me acting like nothing is unusual. i was sure i was busted, but he was also using a cell phone.
 

r97

Measure twice cut once
Messages
3,793
Reaction score
9
Location
Massachusetts, USA
yea some of these laws are like, what?????, who got hurt using a micro wave and sewed MA to have that law put in????? i'm allowed to use any size welder i want, but the second someone pays me to do it, its illegal.

p.s. nothing to break on re-coil starter??? trust me its not fun to brake the little rope :mad2:
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
no like the ones you wrap up every time to start. re coils are a nightmare ive sliced my fingers so many times winding them.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
ok so as for the briggs i need a head gasket and a head bolt.... i bid a recoil off ebay and won, it says its new. $10. so also i need to figure out how to get the old headbolt out (tried everything) and figure out how to open up the updraft carb, it seems as though its not splitting even though all the screws are out.
 

Rustydog2010

NZ Nutta :|
Messages
945
Reaction score
2
Location
New Zealand
Tried everything?

A guy snapped a head bolt on a Honda race car, and we just drilled a hole and used a easy out set...
Worked a charm.

Never say never.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Weld on a nut? If it's a mig, use high heat and low speed so you get ample hold without filling it up too quickly.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
i dont have acess to a welder. i also dont have acess to a torch. as for the steel drill bit, it was brand new. it was an inch shorter when i was done, and there was barely a mark on the bolt. when there was still some left sticking out, i poured wrench oil over it. i banged it with a hammer, and then tried channel locks. that didnt work so i tried a vice grip, and i held the engine steady while my dad gave it a go, didnt move so we banged the vice with a hammer. didnt work either, and snapped even more off it so now there is nothing to grab. also my dad missed and busted off a fin in the flywheel. this is a nightmare!!
 

Rustydog2010

NZ Nutta :|
Messages
945
Reaction score
2
Location
New Zealand
If you broke a fin on the flywheel, it is normally common practice to snap one off DIRECTLY opposite. Thats what I did on our big chainsaw, and it still goes sweet.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
its one of the really thin fins where the magnets are, the only part that isnt cast iron. it barely weighs anything (the broken off piece) and the cast iron flywheel is huge so i dont think it should really be a problem..... tomorrow im going to try to grind a slot in the tiny bit of bolt thats left and jam a flathead in it and attach a vice to that and turn. hopefuly it works, if it doesnt, than i will have to bring it to some auto shop because i may need a drill press to drill it out.
 

redsox985

Active member
Messages
4,092
Reaction score
12
Location
PA
Center punch and drill press out. Get some super strong bits. Maybe diamond edged?
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
okay guys im putting this one aside. i spent 30 bucks on the wrong pull start. i have other projects and things to do before it gets cold. this could be a project for next spring or i may sell it as parts.

sigh... i wish i never opened up that head.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
alright its been a while but today i decided to throw it together without the one headbolt and it feels like it has alot of compression... testing it tomorrow!!
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
It runs!!!!!!!!!!!!!!!!!!!!!
Yes!!!!!!!!!!!!!!!!!!!!

but then........ sheared the flywheel key. :censored::censored:

[/IMG]
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Well if anyone is still reading this....

What a monster it is with no gov and a straight pipe. It shoots fire every time the engine fires and when it backfires it really makes fire. Its really hard to start though.... Lol sounds like a car running no manifolds though. BLOOP BLOOP!

I need a vid... It was too dark today but maybe wednesday if i have time.
 

Lynx_Genisys

New member
Messages
194
Reaction score
1
Location
Alberta, Canada
haha.. sound slke you're having fun..

as for no money, get a paper route, shovel sidewalks, and mow lawns etc..

lotsa "Privateer" things you could do..

I know it almost sounds lame, but someones gotta do it, and thats what i did as kid..

plus if you manage to buy yourself a cheap riding ower, we use ours as go-karts/bu,per cars as well.. hehe...

its funny.. my lil bro in law has like 3 lawn tractors now.. i was buggin him to let me turn one into a kart.. lmao..

one he uses for yard work, anotehr he uses for lil tractor pull sand smah up derby, and another jsut for riding around on and draggin thigns around.. ahha..

he rides it more than his race prepped KX (KDX?) 125 lol

that engine looks very much like the one that was on my very first go cart.. lol
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
Yup its done now though. It siesed up but the rod is still in tact. I was like wtf. It will probably never run again.

I tried drilling out the tap, jist to see if it would do anything, and it deflected the tap, jammed in the aluminum, and snapped my brand new bit.

Ugh..
 
Status
Not open for further replies.
Top