6hp B+S vanguard '05 reduction box removal.

Status
Not open for further replies.

Carlman

New member
Messages
162
Reaction score
1
G'day all,

Picked up a kart with a '05 6th vanguard with reduction box with wet clutch. Just wondering if it's possible to remove the box and have a usable shaft left?

Also I have no experience with Briggs motors regarding governers , anyone have a howto?

Cheers guys.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
You can expect your engines output shaft to look similar to the left end of my top pic:
Without some serious machining a clutch wouldnt fit and work, besides that your output shaft is probably too short anyway:



Below is a pic of a standard non-gear reduction briggs crank for comparison:
 

Carlman

New member
Messages
162
Reaction score
1
Just took the reduction box off, it was a wet multiplate clutch with chain going to the jackshaft. Clutch plates were worn out.

But it left a 3/4" keyed straight shaft left, just as normal...

Guess I got lucky!

Minibike here I come!
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
Good deal man, I'm glad that worked out for ya.

How long is your output shaft?

We ran across a similar situation here a while back, I cant remember what brand/model his engine was, but I seem to remember his wasn't equipped with an oil seal at the crank. Does your engine leak around the output shaft when you tilt it?
 

Carlman

New member
Messages
162
Reaction score
1
Normal length shaft mate, enough for a cent clutch.

Yea it does have an oil seal, all ready to rock!
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I also have a 2:1 wet clutch reduction box on my GX140. I have just has it refurbished, cos the gears were also worn out. If it is cheaper to get new clutch plates that a cent clutch, why don't you do that. I am not sure what they cost there, but might be worth looking into. It does however give you a 2:1 reduction, and you might not like that.

You might also be able to fix the box up and sell it. They are generally quite expensive here in South Africa. Maybe you could regain some of your expenses this way......Just a thought....
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I thought i would post a pic or two of what my reduction box looks like. Just for the fun of it....:biggrin5:
 

Attachments

  • 04122010080.jpg
    04122010080.jpg
    78.9 KB · Views: 8
  • 23112010016.jpg
    23112010016.jpg
    94.8 KB · Views: 7
  • 271120100499.jpg
    271120100499.jpg
    212.6 KB · Views: 6

Carlman

New member
Messages
162
Reaction score
1
Cool kart mate.

Ok, now when I start the motor it's on half choke and it's like a fast idle, full choke and it doesn't run and No choke it revs it's tits off....

Any ideas guys, allready cleaned carb out and I think idle screw is set right.
 

anderkart

Moderator
Messages
6,432
Reaction score
392
Location
Surprise Arizona USA
I'd probably make sure your intake gasket isnt just leaking first. (spray some carb cleaner around it and see if you detect
any sudden change in rpm)

Does your carb, linkage rod and spring look like this pic?

 

Carlman

New member
Messages
162
Reaction score
1
I forgot to mention that I checked all intake gaskets and sealed them with gasket sealant.

And no my throttle setup is different...
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
what horsepower is it?

OHV or flatty?

go to the briggs website, punch in the model and code #'s, and there is a free exploded manual. make sure its setup just like that engine would be.

EDIT: just saw its 6hp.
 

Carlman

New member
Messages
162
Reaction score
1
05 6hp OHV Briggs vanguard. The throttle setup is made for a kart. I don't think it came like that...

I'll have a squizz later, cheers.
 

Carlman

New member
Messages
162
Reaction score
1
Fixed it...mostly lol

It had too short of a spring from the throttle lever to the governor arm.

It just randomly stalls after idling for a few minutes now... Haha

And the pullstart is dodgy so it needs replacing.
 
Status
Not open for further replies.
Top