6.5hp engine stall

Status
Not open for further replies.

Jalers

New member
Messages
5
Reaction score
0
Location
Kincardine, Ontario
Good day,
I have a Powerfist (Princess Auto) 6.5hp Honda clone engine. It is brand new last year.
I installed it into an atv with a Hilliard clutch.
It starts and runs fine. When I run full throttle, and let off the throttle, it stalls out. When I get to a stop, it starts right back up? This has been happening since brand new.
I have adjusted the idle, and no change.
i did remove the gas tank, and ran a gas line from the ATV gas tank into the carb. About 3' of hose. I also welded on a larger Diameter pipe to the exhaust to get the exhaust out the back of the ATV.
Any ideas?
Thanks,
Jay
 

Attachments

  • engine.jpg
    engine.jpg
    23.5 KB · Views: 15

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
If you disconnect the oil sensor, use it for a kill switch, inline with a momentary on button and connect to ground. it makes a great remote kill.
 

Jalers

New member
Messages
5
Reaction score
0
Location
Kincardine, Ontario
It does not stall during operation. Only when you abruptly let off the gas to slow down or stop. if i feather the throttle while on the brakes, i can keep it going....
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Have you modified the engine in any way? Sorry, I just re-read your post. I straight piped my GX340, and it was *almost* stalling on decel. After I fabbed my new muffler, the problem solved itself. Sounds like some carb adjustment is in order.
 

Jalers

New member
Messages
5
Reaction score
0
Location
Kincardine, Ontario
UPDATE....
So i started to mess around with the springs that attach to the throttle lever on the engine. It operates another butterfly....or possibly the governor on the carb?
Now, it does not stall, but will not start to increase engine rpm until half throttle, and way less pickup....I went the other way, and when i started it, it took off...i barley got a hold of the brake!!!
 

Jalers

New member
Messages
5
Reaction score
0
Location
Kincardine, Ontario
Another update....
We blew the dust off the ATV...got it running, and it still stalls on de-celeration...Anyone have any ideas on what to look at?
It fires right back up after the stall.
I cannot figure this out.
 

slideways

New member
Messages
575
Reaction score
6
Your low speed jet is too small.... thanks EPA emissions nazis. Does the motor stumble a tad if you just launch wide open from a stop?

Try to run the motor with the choke about 1/3 or 1/4 way on and see if this helps it. If it does that's your problem.
 

Jalers

New member
Messages
5
Reaction score
0
Location
Kincardine, Ontario
Thanks for all the help on this dilemma...
I was reading another thread regarding how to add a kill switch, and they person said to dis-connect the low oil sensor...and this will also fix stalling over bumps, and hard turns.
So I dis-connected the sensor, and BINGO!!!! No more stalling. Problem solved!!!
Thanks for everyone's help. What a relief
Jay
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
Thanks for all the help on this dilemma...
I was reading another thread regarding how to add a kill switch, and they person said to dis-connect the low oil sensor...and this will also fix stalling over bumps, and hard turns.
So I dis-connected the sensor, and BINGO!!!! No more stalling. Problem solved!!!
Thanks for everyone's help. What a relief
Jay

This was mentioned earlier in your post. With newer Honda Clones, that is usually always the problem.
 

Linkster999

New member
Messages
5
Reaction score
0
man i had the same problem and solved it buy hooking a small black spring from the govenor arm to the fuel tank stud this will allow for it to idle and then u need to adjusrt ur idle speed so that it holds the butterfly on the carb open ever so slightly this should make for a nice low idle
 
Status
Not open for further replies.
Top