5hp briggs...low idle only

Status
Not open for further replies.

dduley

New member
Messages
12
Reaction score
0
Helllo,

I have a 5hp briggs on my dingo. It was running fine then all at once it tried to stall but didn't.. About 5 Secs. later it did stall. Now I can get it started after 478 pulls (just playing). After a few pulls it will start but will only run a short while. If I give it gas it dies.

I have taken the carb off and cleaned everything. But had the same problem.

Any thoughts?

Thanks
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
This sounds like it may be getting either too much air or may be running too lean. Take the spark plug out and give a description of how it looks. If it is getting too much air, it seems t be time to replace your gaskets on the carb. It it is running rich, you need to re-adjust your mixture screw.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I agree with the gaskets. They might look new, but you can check by running the engine and then spraying some carb cleaner round the gaskets. If you hear the engine revving a bit, then your gaskets aren't sealing correctly and are sucking in the cleaner.
 

klicky96

New member
Messages
558
Reaction score
1
Location
Sandusky, Ohio
I agree with the gaskets. They might look new, but you can check by running the engine and then spraying some carb cleaner round the gaskets. If you hear the engine revving a bit, then your gaskets aren't sealing correctly and are sucking in the cleaner.


i use this method a little too much I think ha.
 

dduley

New member
Messages
12
Reaction score
0
Well I was wrong on what is going on.

FYI... This is a horizontal carb if it matters.

I get fuel to the upper bowl in the tank. But The carb is not pulling the fuel up the main jet.

When I said it would only low idle I was wrong. That was the starting fluid burning off.

Yhe jet is clean, I can spray thru it.
Any thoughts on this one?
Sorry for the mistake on what was happening.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Well I was wrong on what is going on.

FYI... This is a horizontal carb if it matters.

What could be happening is that the shorter pick up tube that goes into the top bowl in the tank could be blocked, and the fuel is not even getting to the jet. Take carb off and blow through that pick-up and see if it is clear.

Your diaphragm could also be in need of replacement. This is your 'fuel pump', and if it is old or worn it won't be able to pump the fuel into the carb.

Look at the pic to see what I mean about pick-up and diaphragm. (just in case you not sure)
 

Attachments

  • _briggs_horiz_pulsa-jet_adj.jpg
    _briggs_horiz_pulsa-jet_adj.jpg
    47.2 KB · Views: 0
  • _pump_diaphragm.jpg
    _pump_diaphragm.jpg
    61.1 KB · Views: 0

dduley

New member
Messages
12
Reaction score
0
The pick up is clear.. I can blow through it just fine.

I replaced the diaphragm about a month ago. I took it out last night to check it out. It doesn't look bad. The part where the spring is was stretched out a little. But I didn't see anything else.

Does the diaphragm pull the fuel up the pickup to the jet?

Or does it just pump the fuel to the upper bowl in the tank?


I understand how the diaphragm works. I just don't know if it also pulls the fuel from the upper bowl into the carb.
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
The pick up is clear.. I can blow through it just fine.

I replaced the diaphragm about a month ago. I took it out last night to check it out. It doesn't look bad. The part where the spring is was stretched out a little. But I didn't see anything else.

Does the diaphragm pull the fuel up the pickup to the jet?

Or does it just pump the fuel to the upper bowl in the tank?


I understand how the diaphragm works. I just don't know if it also pulls the fuel from the upper bowl into the carb.

Have a look at this site. It shows you step by step how these carbs work.

http://www.compgoparts.com/technicalresources/briggscarburetors.asp
 

dduley

New member
Messages
12
Reaction score
0
Wow!!!
Thanks for the info..

But I still don't understand why it's not pulling or drawing the fuel up to the jet. I can blow through the pickup tube. I even took a very small (very small) wire and pushed it through the hole until it came out the the bore of the carb. Still no luck.
:worried2::mad2:
 

dduley

New member
Messages
12
Reaction score
0
Going to pick up new ones today...What if this doesn't work? Should I just dig a big whole and park the kart in it?
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Going to pick up new ones today...What if this doesn't work? Should I just dig a big whole and park the kart in it?

LOL. No, we will help you through it. While you are getting new gaskets, you might as well get a new diaphragm just in case the old one is faulty.

You might want to just make sure that the spring that goes behind the diaphragm is not worn, bent stretched etc. That also could make a difference. There should also be a little metal ring that goes over the spring. Make sure you have that too.
 

dduley

New member
Messages
12
Reaction score
0
Okay,

New diaphragm, new gaskets, and the spring and cover looked good.

Now it will run after a few pulls. But, I can't get it to idle down..I turned the idle all the way out (it is removed) and made sure the plate was not sticking open. All was well...Still idle so fast I had to remove the belt before I had to chase it around the block.

One more thing (might be the most important) I started the mixture screw about 1.5 turns out. After it started to run I thought maybe that could be the cause of the high idle. I made small adjustment both ways. I never notice a change. I turned it all the way in and still ran w/o change. I totaly remove it and it still ran w/o change... Shouldn't some type change happened?
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
Okay,

New diaphragm, new gaskets, and the spring and cover looked good.

Now it will run after a few pulls. But, I can't get it to idle down..I turned the idle all the way out (it is removed) and made sure the plate was not sticking open. All was well...Still idle so fast I had to remove the belt before I had to chase it around the block.

One more thing (might be the most important) I started the mixture screw about 1.5 turns out. After it started to run I thought maybe that could be the cause of the high idle. I made small adjustment both ways. I never notice a change. I turned it all the way in and still ran w/o change. I totaly remove it and it still ran w/o change... Shouldn't some type change happened?

I am glad that you have gotten it to run (sort of). Yes, something should definately happen. It should either rev high, or starve of fuel. Your symptoms tell me that your carb isn't totally clean yet. 1.5 turns out is also correct to start with

If you take that idle needle out and look in the hole, you should see some holes. What you need to do is poke those out with some thin wire. What I usually use is a strand of wire that I pull out of my wire wheel (pic below). You can also use the metal strand that you get in those bread twisty ties.

You might not have all the holes that you see in the pic, but whatever you have, make sure that they are clear of any blockages.

I am pretty sure there is just something being blocked somewhere.

Have a look at this site for some more info

http://outdoorpowerinfo.com/repairs/briggs_pulsa-jet_horiz_fixed.asp
http://outdoorpowerinfo.com/repairs/briggs_pulsa-jet_horiz_adj.asp
 

Attachments

  • _discharge_ports.jpg
    _discharge_ports.jpg
    18.7 KB · Views: 1
  • SEABG150-WW2.jpg
    SEABG150-WW2.jpg
    65.9 KB · Views: 0
  • 030.jpg
    030.jpg
    5 KB · Views: 0

dduley

New member
Messages
12
Reaction score
0
Wow you are full of info arent you....

Okay I got the elbow plug out and clean those 2 holes. But I'm haveing trouble getting the "idle fuel mixing well" (image 17 on your first link) plug out. Any ideas on getting this out with out messing it up.

Thanks again for all your help. I got this kart for my boys and it has been one headache after another. I bought it used because I was being cheap that day....Should have bought a new one...lol
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
I know with my carb, i left all the welch plugs in. I did not touch them. I would just make sure all the holes you can see are clear. If that doesnt work, then i suggest take it to a small engine repair guy who can take the plugs out and also then replace.

It is better buying second hand cos it is cheaper, and you learn how to fix things. As long as u can blow thrnugh the pick up, it should be clear
 

dduley

New member
Messages
12
Reaction score
0
It is better buying second hand cos it is cheaper, and you learn how to fix things. As long as u can blow thrnugh the pick up, it should be clear

Sometimes..Yes... But that seems to be the case with everything I buy. I always have to fix something before I get to use it....lol..

I have messed with ALOT of things in my time. Not going to state my age....but you get the point. I do know my way around most things, just not small engines...Guess its time.

Thanks again... I'll keep you updated.
 

dduley

New member
Messages
12
Reaction score
0
you still with me?????

I have an update.

I got everything put back together and it seems alot better. Still wants to idle a little high. I noticed that when I rev it and let it return to idle it seems to idle fine for a short while (2-3 Secs.). But after that its right back to idleing higher.

I'm also still sucking a little air between the carb and engine. I gave it a shot of cleaner around it, then it idle up. I'm going to take it off again to make sure I got all the old one off. But do you think this is why I'm still idleing a little high?
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
you still with me?????

I have an update.

I got everything put back together and it seems alot better. Still wants to idle a little high. I noticed that when I rev it and let it return to idle it seems to idle fine for a short while (2-3 Secs.). But after that its right back to idleing higher.

I'm also still sucking a little air between the carb and engine. I gave it a shot of cleaner around it, then it idle up. I'm going to take it off again to make sure I got all the old one off. But do you think this is why I'm still idleing a little high?

Sounds like we are getting somewhere

Air being sucked in could be your problem. I would make sure that there is no air being sucked in before we go any further. Make sure that the gasket you have is the correct one, and that the block and carb are clean of any old gasket material, grime, etc that might cause it to suck air. I sometimes find that if you smear a little bit of vaseline on the gasket (just a little), then it seals a lot better.
 
Status
Not open for further replies.
Top