4hp Kohler k141

Status
Not open for further replies.

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
j.concepcion54321, here is the link to the thread where I tried electrolysis on my chain. It turned out really well. Better that I expected. Because I have a triplex chain, it would have cost be big bucks to buy a new one.

Let me know if you have any questions
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
thanks alot landuse i do have one question though. does it have to be done with a bttery or a charger? cause i was planning on using an ac adapter that outputs like 9 or 12. will that still work?
 

landuse

Moderator
Staff member
Messages
18,804
Reaction score
613
Location
Pietermaritzburg, South Africa
thanks alot landuse i do have one question though. does it have to be done with a bttery or a charger? cause i was planning on using an ac adapter that outputs like 9 or 12. will that still work?

I am not 100% sure, but if it can output the same as a battery charger it should be fine. This method of removing rust is really awesome. The only limiting factor is the size od the bucket you use. I use "Soda Ash" (proper washing soda) to make my electrolite solution. I just picked up a packet in the pool products section of our local store. I think you might have a product called Arm and Hammer Washing soda. Its the same thing.

Also just make sure that you hook the charger up the right way, cos if you don't your metal will be eaten away instead of being cleaned up. Here are a few more links that might give you more info.

http://www.instructables.com/id/Electrolytic-Rust-Removal-aka-Magic/
http://myweb.tiscali.co.uk/andyspatch/rust.htm
http://www.antique-engines.com/electrol.asp
http://www.davidbradley.net/ERR.html
http://www.1bad6t.com/rust_removal.html
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
Update: I'm starting to work on the carburetor to see if I can get the throttle and all the butterfly arms and such to break free. If u remove the governor would I have to put a tachometer to make sure I don't go over on rpms???
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
Update: I took the gas tank off, removed the spark plug, and took the carb off.

i started to work on the carb and i got the throttle working, but the other lever still doesnt move. i think its the choke but im not sure. will post some pics tomorrow.

Things to come: Take off crankcase cover, clean insidde of engine, get new spark plug, finish up carb, try to start engine.

Questions: Is this engine supposed to have an airfilter because i dont see one anywhere?? I found a 12volt 1amp transformer, can i use that to do the electrolysis on the tank? can i use baking soda for the mix instead of washing soda??

More to come,
Thanks
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Baking soda supposedly works, just slightly less effective. Your transformer offers only one amp, so the process will probably be slower. Be patient. And watch your polarity! Having it backwards will de-rust your electrode and eat away the part you're trying to save. Speaking of which, what part are you planning on performing the electrolytic rust removal on?

There's a chance your engine did not come with an air filter. Snowblowers quite often do not. Depends on original purpose of engine.
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
does it not having an airfilter affect the performance, if it does how can i make a cheap makeshift one? i wanted to do the electolysis on the gas tank so tht i can use it again.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Okay- just wanted to make sure you weren't going to try it on the carb. Rig an air filter any way you can. Letting your engine inhale solid matter is a death warrant. Order an aftermarket air filter (high flow) and figure out an adapter.
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
what can i use at home?? i have some foamy insulation stuff for boxes and some pvc pipe. will that work?

ok so i have all day tomorrow to work on the engine. WOOT!! ill see if i can get it started!! does hey toystory do you by any chance know how i could free up that choke on the carb??

thanks
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Umm, yeah? Have you tried submerging the entire carb in a bath of WD40, or Fluid Film or something for a few days?

I forget the proper term for the chemical process, but when steel and aluminum are mated for too long under the wrong circumstances, it'll get ugly. Soak the wee out of it for a few days. Try applying some heat, too.
 

j.concepcion54321

Rebuilding KTM, Need Kart
Messages
1,251
Reaction score
5
Location
East Providence RI
ok ill pick up some gas and wd 40 to soak it in. does it helpto take it apart and clean everything thats rusted up with a wire brush and then put it back together?
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
It sounds like total disassembly is your only option. Soak the whole mess submerged in WD40 for a few days, and gently start to work the choke lever back and forth. As soon as you can, take the choke plate off and work toward removing the shaft.
 
Status
Not open for further replies.
Top