440 snowmobile engine swap

Status
Not open for further replies.

Auker1

New member
Messages
10
Reaction score
0
Location
PA
I have a gokart frame that I put an old alouette 440 in that I got for free. It came with the drive clutch but not the driven. I cant seem to id the drive clutch. Prolly cause its so old. I was wondering if anyone had any ideas as to what drievn clutch I need or one that is close. Doesnt have to be fancy. I will try to get pics soon.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
If you're going to attempt to source an original driven, you might have a tough time figuring out the correct belt and pulley spacing. It might be worth your while to carefully measure your PTO shaft, and source another drive unit, driven unit, and belt as a complete kit.

Who manufactured the donor machine? Have you attempted to contact the manufacturer for info?
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
I have the original belt. Or what was one the machine when the engine was removed. I did not remove the engine. The manufacturer was alouette. I haven't contacted them. The engine is a 1973. Idt alouette is around anymore. I haven't been able to pull the primary clutch. I'm going to work on that this week.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
I did some googling after the fact, and came to the realization that Alouette was the brand name. I figured that it was a model, likely from Bombardier given the age and French name. Perhaps you can find a forum dedicated to such things and get the required info from folks that might know for sure?
 

exenos

Project Nut
Messages
1,217
Reaction score
0
Location
Ontario, Canada
You cannot swap out the primary clutch for another one. The only thing you can do is figure out what the belt width is and find a secondary clutch for that width of belt. Then ask around on a few sled forums for the center to center distance for the clutches and set it up that way. You may have to do some fine tuning on the secondary to get the clutches to shift properly.
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
ok i have a secondary from a polaris indy lite 340. i set it up and the main clutch engaged and the secondary clutch spilt apart like it should but didn't go back together. im assuming that i need a secondary from a 440 engine that has the same belt width and shaft diameter? i have the shaft center measurement.
 

exenos

Project Nut
Messages
1,217
Reaction score
0
Location
Ontario, Canada
The 340 secondary is probably fine because a more modern 340 should have the same if not a bit more power than your older 440. When the secondary opens, then doesn't close is the primary opening back up or is it staying contracted? Both the clutches probably could use a cleaning and that may solve the sticking clutch.As for the belt width, the belt should be siting around 1/8 to 1/4 of an inch above the secondary with it fully shut.
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
The 340 was an older machine too. Mabe not as old but not new either. Would it be helpful if I would upload a video of what happens when the clutches engage? I did clean the secondary and it seemed to work a little better but it still didn't contract correctly.
 

exenos

Project Nut
Messages
1,217
Reaction score
0
Location
Ontario, Canada
The oldest the lite could be is 1980 and I consider that to be a "newer" sled because that's around the time that they really started to advance, expansion chambers, exhaust valves, reeds. And yes pleas upload a video so we can see exactly what happens.
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
ok so i didn't have enough daylight this evening to get a video of it but i did take some pics. i also took it out and tried it again. The main clutch engages too quickly but that is a problem for another time. The clutches engaged and the main clutch slipped a lot on the belt. Idk if my belt tension was wrong or if i need a new belt or if i need a new spring in the driven unit. i am new to this forum so idk how where to upload pics. little help?
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
here are some pics. idk how much this will help but ill try to get a vid asapIMG_0237.jpg

IMG_0236.jpg

IMG_0234.jpg
 

exenos

Project Nut
Messages
1,217
Reaction score
0
Location
Ontario, Canada
When I'm looking at the secondary it looks like the heilix (spring) is wonky, is that just me or is it actually like that?
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
Yes it is pretty weird. In that pic I have it wound almost as tight as I can get it. Idk if I was supposed to wind it that tight or not. It seemed to help with the rebound.
 

exenos

Project Nut
Messages
1,217
Reaction score
0
Location
Ontario, Canada
Just took another look at it and I think the secondary might be on backwards. Which way does it expand? To the inside or outside?
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
Ok is that the only problem? Can I get a different driven unit that moves inward and will work with the main clutch?
 

Kaptain Krunch

Pro Junk Collector
Messages
4,636
Reaction score
6
Location
vermont
Secondary is definitely on backwards. Flip it around and try again. For the most part you you should be able tune any clutch to any similar clutch (similar motor, same belt width). due to the amount of power your putting to that relatively small looking kart, i wouldn't be too worried about tuning the clutches until you get it moving. If it doesn't have enough torque and seems to shift out too quick, tighten up the secondary spring, if it feels like it doesn't shift fast enough and winds out too far, loosen the spring.

If the primary and secondary are too far off, you may have to change springs in one or the other. If you cant get it to shift out all the way even when the secondary is adjusted as loose as possible, you may need heavier weights and/or a lighter spring in the primary, and vice versa if it shifts too fast.
 

Auker1

New member
Messages
10
Reaction score
0
Location
PA
My secondary only goes on one way. The way it is now the shaft slides in and stops. Can I just drill out the center to the shaft size so it goes the whole way on only backwards?
 
Status
Not open for further replies.
Top