1960's 6hp techumseh

Status
Not open for further replies.

Bluethunder3320

New member
Messages
5,677
Reaction score
39
the kart i just bought today on craigslist came with a old techumseh off a arien's snowblower. its painted white and looks horrible, flakes rust everywhere.

what i'm trying to do:

modify or make a manifold to put on my 8hp briggs carb (was missing a carb)
find a clutch that has 5/8 bore
figure out the year it was made exactly
polish the "guts" under the head
remove the old rusty governor (weld the hole shut)


I NEED HELP WITH THIS:
i removed the flywheel to clean the points, now how do i put it back? i hit it with a hammer but the keyway keeps sliding all over the place!
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
The keyway itself does not move, that is the slot. The key might move if its slightly worn but it should be fairly snug if tapped gently into place. My only suggestion is tap it into place gently and then install the flywheel as far as that problem goes.

If I were you i'd get a conversion kit to electronic ignition, they're easy to find and inexpensive. Heck, even K-Mart sold them for years.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
thanks sorry i got key mixed up with keyway

its just when i push the flywheel on it it angles up and moves back and the flywheel wont stay. maybe i can hold it with a flathead screwdriver?

wait, but how do the CDI's mount onto the motor? there isnt magnets on the flywheel and no place to hold a coil obviously and i dont want to spend much.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Search online for a moment, the ones we purchased years ago cost about 5 dollars each, I'd think many you could find would be less than 10 just a decade or so later. :)

On the key, be very careful you don't wedge the key in improperly or pinch it, though keys are not very expensive if you do destroy it.
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
Do you mean that it has a woodruff key and it keeps on turning out of it's turning out of it's key way? Or that it has a standard key and that keeps on getting hooked on the flywheel and moving.

As Blaz says, electronic ignition kits are cheap and you will probably never have with the ignition system again with one, if the points are fine I'd leave it though. The condenser might be dead given the the condition of the engine.

If I were you i'd get a conversion kit to electronic ignition, they're easy to find and inexpensive. Heck, even K-Mart sold them for years.

You have K mart over there? Wow.

Thanks

Hayden

Edit: ****, I'm too slow.
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
wait, but how do the CDI's mount onto the motor? there isnt magnets on the flywheel and no place to hold a coil obviously and i dont want to spend much.

You cut the wire that goes to the points and attach that wire the the ignition module, another wire comes off that wire and goes to your kill switch, the electronic ignition kit is just a little tiny box (the ones I've seen are about 2cm x 2cm x 1cm), not the whole coil and magnet set up.

Thanks

Hayden
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
ahh thanks, im gonna buy that clutch and most likely the CDI. points are like 8 bucks anyways.

anyways heres a pic of the motor before rebuild. all kinds of things were growing out of it, lol.
 

Attachments

  • IMG_2050.jpg
    IMG_2050.jpg
    94.5 KB · Views: 3
  • IMG_2051.jpg
    IMG_2051.jpg
    90.2 KB · Views: 3
  • IMG_2052.jpg
    IMG_2052.jpg
    76.3 KB · Views: 3
  • IMG_2055.jpg
    IMG_2055.jpg
    101.5 KB · Views: 3
  • IMG_2056.jpg
    IMG_2056.jpg
    89 KB · Views: 4

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
You plan to buy the one on ebay and the one from the link I sent you?

Its the same item which is from the Oregon catalog? Do you have 2 engines that need this product, if so get 2 of the less expensive one.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
dam my exhaust is rusted to the block. i wanna put on my clean briggs muffler but i cant break the old pipe free.
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
usually you can heat up the amuminum block preety good and bust those free. But itll probrobly mess up the threads a little. Usually theres enough bite left to put a new one on though. Make sure you make the flywheel nut really tight when you pu tit back on and dont put greese or anything on the taper because it uses that to hold itself in place. Also are you sure thats a 5/8 shaft? because iv never seen a 5/8 on anything bigger than a 4hp
 

porsche930dude

New member
Messages
906
Reaction score
29
Location
Upstate, NY
well do you know what all the factory specs are? hell if i do. im just sayin if you dont then the key can strip out . I know iv had to make some alot tighter than the factory ever would have because hop up parts can jerk it around so much that the key sheers. briggs motors have an aluminum starter cup. explain to me how you get a torque wrench on that?
 

Russ2251

AZUSA:Powered by LAWN-BOY
Messages
6,622
Reaction score
47
Location
Huntington Station, Long Island, NY
well do you know what all the factory specs are? hell if i do.
That's obvious.
im just sayin if you dont then the key can strip out .
Not possible.

Torque specs are in the manual. Freely available on-line to anyone.
Under torquing can and does cause keys to shear.
Over torquing can and does cause flywheels to fracture.
Specs are specs...despite any "hop ups".
Flywheel nut is torqued...not starter cup.
Starter cup is held on with flywheel nut.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
my torque wrench does up to 200 lbs whatever that means. i need to find the specs for this motor,

its a tecumseh h60 that came off a airein's snowblower.

its in bad shape as you see but thats why im fixing it up.

just to let you know about 1 cup full of rust has came out of this thing so far. oh and i found out the governor is snapped inside the block, so im removing it.

another problem, i took the bolts off the rod but i cant get it apart and i dont want to dent it.
 
Status
Not open for further replies.
Top