Search results

Thanks for all the advice from everyone. I order new parts come Payday. I start pulling it apart and welding and paint again! :(

With that 60 tooth how much clearance do you have. I believe you going need to use a JS specially using the #35. But I let the others experts chime in on this.

What I am thinking is for the one that is bent is to replace it and install a pillow block in the center. Then and the rear JS moved all the sprockets to the far left. Then cut the JS in 1/2 and move Pillow over to the left in (center) of current JS. This will reduce the area to about 5-6...

Tell me about it. I think I need to disassemble the whole back again including the engine at shocks. Painting the underside of the new cross bar will be best if I can flip it.

Thanks Poboy, moving the sprockets close to the wheel will make more since. Shorting the Jackshaft between the pillows will make it stronger. Thanks again for all your help. I will need to order some new parts and do some more welding, painting etc. Dang!

Poboy, Not sure if I understand. Are you basically say to shorten the length of the jack shaft between the jack shafts. My thought was to add a pillow block in between the torque and the 10T gear. This will give a spread of only about 5 inches. ??? ---------- Post added at 12:44 PM...

Well something went wrong on my first trip. I went around the street this AM and heard a thunk about 5 mins in When I got in the drive way I noticed the jack shaft (3/4") is bent. Just for info My TC40 is on the JS with the 10T which goes to the 2nd JS with a 29T. Then the 2nd 10T which...

I purchased a knockoff 40 on ebay for my 13HP. The driven I requested with a 3/4 " for the jackshaft. If you need I can post the ebay link.

LOL... My wife made sure I marked it with a sharpie pen with "brake fluid"

What I learned today I thought would be very helpful to pass along to the rest of this forum. I was having serious issues bleeding my new disk brakes as I was getting air into the system. Everything I tried to get it out I was not successful. After several minutes of google and youtube. I...

Kelly, I got the stock air box off and was able to put a nice strong sping on it so it returns back to home. Throttle working good and it reving up nice like a caged lion... Just to get this #$#$%^@$@ brakes bleed correctly. Still getting air in the lines. Reading several suggestions now.

Just curious question why thread is moved from general question to Engines?

Got much more done this week. Slower at work for a few days.... I got the engine and double jack shaft with my TC 40 on the swing mount. Front wheels and tie rods back on. Gas and brake are now connected. Just to adjust the hydraulic disk brake and bleed the lines. Then we can test it out...

It was misleading on this nut inside. Turn out there a nut there attached to the throttle arm. But not bolt in it. I was able to get the air housing off and got a strong spring added for a turn to home (idle).

It would be nice to have on icy roads right now...

Predator 420 : HELP Remove stock air box So I need to make some changes to the throttle on the predator 420 engine. To access the throttle screw downs I need to Remove stock air box above the carb. I see there to nuts on the outside. Removing the lid there 2 screws. But there one nut under...

I thought I was loosing my mind today. I had big plans to get everything inplace today on my day off, but that did not happen. First mother nature delivered wet and ice today on our endless amount of snow. But I could not get the throttle cable to return to a idle state so the engine was...

$450 ouch... Thats much more than we pay for the motor itself. It will be nice to know what difference people see after the upgrade.

Anyone have ideas on the the orientations of the spring away vs inside or toward the engine? Do I need to install a yellow spring for reverse?

Denny, Thanks for your reply. I thought about the mess floor for a while. My karts sets about 10 inches from the ground. But figured it becomes a issue it will be easy enough to add some cheap tin which can be secured easy enough using the mess as a foundation. I am more worried about the...