Recent content by Kenpilot

  1. K

    Smoking Clutch and slow acceleration starting off

    It says its for engines up to 7 HP. Mine's an old Briggs 8HP. Think it would still be ok? That one is a lot cheaper then the one I've found.
  2. K

    Smoking Clutch and slow acceleration starting off

    Unfortunately its a Hilliard Extremem clutch from Northern Tool. I checked out the clutches from ombwarehouse but unfortunately I need a 1 inch bore 40/41 10T clutch for an 8 HP engine. I've only found 1 so far and its almost the price of a torque converter. Which I would LOVE to have but my...
  3. K

    Smoking Clutch and slow acceleration starting off

    Ok so I went and looked at my kart to possibly fit a jackshaft and there really is NO room to add one. So a couple questions... Is it possible to just change the clutch sprocket from a 14T to a 10T? As in pull of the 14T sprocket and replace it with a new 10T sprocket? Or I'm assuming I can just...
  4. K

    Smoking Clutch and slow acceleration starting off

    Will do, thanks. And yes its a 1in live axle.
  5. K

    Smoking Clutch and slow acceleration starting off

    40/41 Pitch chain. I forget which one. I only rode like 2 or 3 times for about 30 seconds. so not too long. I won't ride it again until I get a bigger drive axle sprocket or add a jackshaft. I'll Probably just add a jackshaft since I can get one locally. Anybody have any good How-to's or posts...
  6. K

    Smoking Clutch and slow acceleration starting off

    Too Low gearing? Too high gearing? Any suggestions on fixing it?
  7. K

    Smoking Clutch and slow acceleration starting off

    Finally finished building my first kart and when I did the first few test runs (on my front lawn) this is what is happening: First, the drive axle spins without stepping on the gas (I've got the idle down as far as it will go without cutting out the engine and it has helped, but the kart still...
  8. K

    Leveling go kart/axles problem

    Correct, engine is at the rear. Its not a competition kart, just a project and something to run around dirt roads and in the woods with. Thanks for the advice!
  9. K

    Leveling go kart/axles problem

    Well i wasn't really looking to have the rear raised, just figured if i was stuck with one end being slightly higher then the other, it would probably be better to have the rear higher, would it not?
  10. K

    Leveling go kart/axles problem

    I guess I should add that ive already cut off the bearing hangers i had so I'm going to need to get new hangers regardless. Just not sure which ones I should get that will help
  11. K

    Leveling go kart/axles problem

    Building my first kart and I just put the rear axle on and the rear tires (front were already on) and I noticed the rear end sits about 1.5-2 inches lower then the front. Unfortunately the problem lies in where I welded on the rear bearing hangers.These are the ones I have so I am very limited...
  12. K

    Which chain for this setup???

    I'm an idiot. Both my drive sprocket and live axle sprocket both say #40 chain. Thanks for the help!
  13. K

    Which chain for this setup???

    Hey guys, I have a 14T clutch sprocket and a 60 Tooth Drive axle Sprocket. Which chain should I use for this set up? #35,40,41,420??? Engine 8HP, 15inch tires. Thanks!
  14. K

    Putting Rear Wheels on Live axle ???

    LOL tempting, very tempting ;)
  15. K

    Putting Rear Wheels on Live axle ???

    Awesome, thanks guys!! Going to go with the new axle mentioned and return the other axle I have.
Top