Recent content by Everett45

  1. E

    Governor 'bypass'

    It's hard to tell the angle in the picture, but it isn't as sharp as it looks. It's on the frame at a 45 degree angle, then goes up a bit. It is actually quite smooth and doesn't cause any problems. As for the engine, yes it'd be a shame if it blew :/ I don't plan on thrashing it, but nor do I...
  2. E

    Governor 'bypass'

    Here's a picture and a little diagram to better demonstrate:
  3. E

    Governor 'bypass'

    My go kart has an 8 HP B&S Flathead. My throttle setup is as follows: cable from the pedal attached to the governor arm, which operates the linkage on the carb. The governor arm has a RETURN spring on it, to allow the throttle to close automatically. I've ran this go kart several times (not a...
  4. E

    Method of seat attachment?

    Got some 1/4" T-nuts, worked like a dream. The unevenness of the sheet metal resulted in one bolt not sticking far enough through the hole, but in the future I'll get a longer one if need be. I did use nylon nuts so they won't be rattling loose. Thanks guys
  5. E

    Method of seat attachment?

    Thanks for all the responses. I think T-nuts sound the most appealing to me. I'll check my local hardware stores and see if they have them. I'd rather not rip these things apart, but it seems that is the only way.
  6. E

    Method of seat attachment?

    My current setup for seats is vinyl leather wrapped wood with foam. On the back of each seat cushion, along with the seat frame, are velcro strips. The adhesive is fairly strong, and it stayed on there for a little while. However, after a bit of use it ripped off the seat frame. Granted, the...
  7. E

    Steering is very touchy

    The welds:
  8. E

    Steering is very touchy

    It's only letting me do 1 at a time:
  9. E

    Steering is very touchy

    To everybody that gave me input: I apologize for not updating you after my project was completed. I guess I was just too absorbed in it all to go back to the forum. Anyways, it turned out great IMO. I have not rode it yet, but I can tell I could've used some more positive caster. From what I can...
  10. E

    Steering is very touchy

    Copy that, I'll shoot for 12.
  11. E

    Steering is very touchy

    I just got my square tubing, and I went home and mocked up my spindle brackets. I took a little protractor, and at 10 degrees it looked about right. What do you guys think?
  12. E

    Steering is very touchy

    Good point about the camber; I think I'll leave it be. As for caster, it sounds like I should do a bit of positive. I'm still open to feedback, I'm putting this all together on Saturday.
  13. E

    Steering is very touchy

    So I've been researching a bit more for my upcoming fabrication project. I completely blanked on any camber or caster implementation, as the Kartfab.com website had the steering setup at all 90 degree angles, no caster or camber. I realize that these may in fact be necessary. My purpose for this...
  14. E

    Steering is very touchy

    Hellion, that's exactly what I'm thinking. My order of new spindles, brackets, tie rods and ends arrived by te end of today. I'm going to pick up some beefy 1x1 square tubing, and fabricate the entire front end. I would like to cut past the pedals, as they are very loose and sketchy, but I'm not...
  15. E

    Steering is very touchy

    I've come up with a sketch of what I want to do. If you look at my first photo, you can see right in front of the pedals where the sheet metal ends and the angle iron is attached, along with the front axles. I'm going to cut along that line, severing it completely. I will cut off the little...
Top