150cc 5 speed engine - $150

[Bwdeaton]

Would like to sell this motor to someon who could put it to good use.

It is a 150cc Honda clone motor with an integrated 5 speed manual transmission. Has mounting plate capable design with a standard go kart motor type of mounting on the bottom also has mounts for lots of other applications.

Started and ran when I bought it. I didn't end up using it for my project. Was on a street go kart that jumped a curb going too fast and bent the frame. The engine includes all wiring to run and a carburetor. No exhaust pipe included.
Can send pictures.

Asking $150 for it, plus shipping if necessary.

 

[Bwdeaton]

Here are some pictures.
http://uploads.tapatalk-cdn.com/20160715/4f332b3cb6787bc57c6ad256215d8659.jpg
http://uploads.tapatalk-cdn.com/20160715/38c1e3bed65b708a21c519bd8af076c6.jpg
http://uploads.tapatalk-cdn.com/20160715/430cbe469484831d4e386a1bfe99cadf.jpg
http://uploads.tapatalk-cdn.com/20160715/05960842c7f41c7675a22e48dfb16164.jpg
http://uploads.tapatalk-cdn.com/20160715/3c22263da2d08d24f25380274bfad6a5.jpg
http://uploads.tapatalk-cdn.com/20160715/180ebe6dddd87b16e8a9c56a287d56fb.jpg


Sent from my iPhone using Tapatalk

 

[chancer]

That thing is gonna sell FAST!

 

[Poboy kartman]

Honda is the new GAB.....

 

[Bwdeaton]

It should make a fun kart or bike for someone who wants a manual transmission. Should be able to be geared for 55-60mph. This is not electric start, which is less convenient, but also saves some weight.
Some more specs.
-149cc displacement
-60lbs wet (with oil)
-9.5 to 1 compression ratio
-max engine RPM~ 9500
-approximately 12hp
-gear ratios
>primary reduction 3.333 to 1 (crank to clutch input)
>1st gear 2.769
>2nd gear 1.882
>3rd gear 1.400
>4th gear 1.095
>5th gear 0.923
Internal parts from 2003-2005 Honda crf150f engines are compatible. This is just a reverse engineered copy.



Sent from my iPhone using Tapatalk

 

[Holybeen]

Estimated shipping cost? If your willing to ship it to Hattiesburg ms

 

[Bwdeaton]

Could probably be sent for around 50-75 to your location


Sent from my iPhone using Tapatalk

 

[Bwdeaton]

I cleaned it up a bit and started it today. It runs good, I took a short video. I'll try to upload the video later tonight.


Sent from my iPhone using Tapatalk

 

[Bwdeaton]

Bump


Sent from my iPhone using Tapatalk

 

[Bwdeaton]

Shipping to most of the US will run about $90-$100


Sent from my iPhone using Tapatalk

 

[Cdh.Sjh.customs]

Where are you sending from and is this still available?

 

[Shamelessbullet]

is this still available

 

[Bwdeaton]

I would ship from Dayton Ohio and will drop off at the shipping provider.
It is still available.


Sent from my iPhone using Tapatalk

 

[Bwdeaton]

I do still have this

 

[jdfelda]

i'm interested in your engine

 

[Loylmongoose]

Is it still available

 

[Bwdeaton]

Yes I still have it, PM me.

 

[bob58o]

How tall from bottom to top.
Suppose I wanted to mount it on a minibike...
How much room would I need between a flat (parallel to the ground) mounting plate and the top bar??

I think I read like 18" or 19" but not sure if that was a 150cc or not.

 

[Bwdeaton]

How tall from bottom to top.
Suppose I wanted to mount it on a minibike...
How much room would I need between a flat (parallel to the ground) mounting plate and the top bar??

I think I read like 18" or 19" but not sure if that was a 150cc or not.

Ill measure it when i get home for you.

---------- Post added at 04:31 PM ---------- Previous post was at 04:06 PM ----------

Measures just under 17 inches from bottom mount to top of head.

 

[Bwdeaton]

How much space is open above a predator 212 in a minibike frame like a baja or something similar? I read that a predator is 14" tall vs 17" so I could see it fitting in a minibike. It would be a neat bike too.