The great flywheel test and video

Status
Not open for further replies.

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
I'm going to make a movie. I need a flywheel.

I've decided to try and tackle the myth of the flywheel once and for all.
If someone has a stock clone flywheel that they're done with, I'd appreciate it if you could send it to me.
I'll give you and your flywheel credits in the movie.

PM for address.

Thanks!
 

B.M.800

TheBeal.
Messages
2,387
Reaction score
26
Location
Central PA
Sorry I dont have an extra flywheel... but, Im sure we are all interested to see how this goes.

How are you planning to spin it?
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Years ago I was going to try to do something like this... A fly wheel break tester...
A couple of guys at a previous work(an electrical motor repair shop) were talking about using a large servo motor...
They will be able to spin at a very precise speed using the controller and will be able to handle the load, they also have a large mount of torque...
All it would need is a matching crank taper adapter and some kind of enclosure to contain the blast......

With a servo.. One could, when hooked up to an appropriate interface computer, simulated a reving motor or long ramped up runs ect... Really find the breaking point.
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I thought OMB member was sending you one.

I guess he would not send it if you did not have a Govna and a billet Rod? LOL HAHAHa
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Make sure you post the video on OMB and probably have a couple engines just to make sure you have a variety in quality. Too bad that this got locked on the Mythbusters page a few years ago, because people who knew nothing came out of the woodwork claiming it would, then turned to bashing each other.

A designer knows he has achieved perfection, not when there is nothing left to add, but when there is nothing left to take away.
 

pRoFiT

Can't buy it?, build it!
Messages
1,151
Reaction score
64
Location
California
How do you really test this. Because one may brake at lower rpm with some added real world vibration. You know driving a go kart. What you need is halt testing facility. Ramp up vibration and cycle cold hot temps.
 

FreeRunner15

=======
Messages
660
Reaction score
10
Location
================
I would like to see how much Torque these stock flywheels can handle as well.

I don't know how precise of a measuring device you are using but it'd be nice to see how much of a jump say from 2250rpm to 5250rpm these things can handle before some kind of cracking.
 

Kartorbust

Inmate #627
Messages
4,605
Reaction score
1,101
Location
Utica, NE
Probably just a small hour/tachometer that wraps around the spark plug...that's about as accurate we have, unless someone wants to come with one that sits above the flywheel that can be more steady to ready.

A designer knows he has achieved perfection, not when there is nothing left to add, but when there is nothing left to take away.
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Why not, if you can contact some engineering students at a local collage or university... They'll have other equipment you won't be able to get easily and some project they'll actually use for there interests as experiments...
 

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
I received a used flywheel from a very generous member (not from here) whose name will not be revealed until the credits of said movie.
In preparation, the flywheel is going to be balanced, polished and magnafluxed or x-rayed to make certain no pre-existing cracks are present.


In preparing for the great flywheel test a thought occurred to me.
How long would a clone run on oxy-acetelene, and what kind of RPM's might one expect?
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
This ones easy. On compression and ignition it will blow up in your face.

Good news and bad news.

Bad: It would be a short vid.

Good: Couldn't make it any worse than what it is.

---------- Post added at 11:11 AM ---------- Previous post was at 11:05 AM ----------

BTW: For a flywheel test....forget internal combustion. Use an electric motor...without a load and a little gearing...20,000 rpm should be easily obtainable.

Make sure you are a safe distance away...( maybe California?) when you test.:thumbsup:
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
Can we get a "Sneak Peak" or as they say in Hollywierd the "trailer"
This Film has not yet been rated.
Coming soon to a Forum near you.
 

Bbqjoe

Banned
Messages
3,455
Reaction score
70
Location
Location, Location
Well I wish I would have taken a before pic, but alas....

Anyways, the flywheel is all polished up, and I'm sending it off to an acquaintance of mine for some magnaflux action. He said he will probably use the EV-6000, whatever that means.
He said he might also even X-ray it as well, depending.

Being as he is doing this on the down low at work, he said he won't be able to provide tangible results, and I'll just have to take his word for whatever he finds.
 

Attachments

  • fw.JPG
    fw.JPG
    125.3 KB · Views: 7

pRoFiT

Can't buy it?, build it!
Messages
1,151
Reaction score
64
Location
California
aw flywheels.

We want exploding flywheel videos!! mass destruction videos! high speed cameras so we can slow it down frame by frame explosions!!!!

---------- Post added at 03:26 PM ---------- Previous post was at 03:24 PM ----------

oh snap. i just acquired a 3100 RPM treadmill motor....geared up maybe could go faster. Maybe not fast enough now that i think more about it....oh well it was a thought.
 
Status
Not open for further replies.
Top