direct connect to carboratur

Status
Not open for further replies.

strikerty

New member
Messages
9
Reaction score
0
I have an old 1975 briggs I put on a manco phoenix eagle II that I picked up for 50 bucks last week. I have been having fun riding it around but yesterday I noticed it seemed to be at rpms one would expect from a rototiller or tractor. I reached back while riding it and pushed on the top of the carburator arm and man did that thing fly. Is there any way to connect the throttle directly to the carborator? Is there any reason I shouldnt ? The govorner linkage is not disconnected when I do this.

Just curious. Grew up working on these things with my dad but it has been years since I did.

Thanks
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Welcome to the forum. There is a thread st the top of this section on governor removal. Read it through, it has pretty much all you need to know.
 

strikerty

New member
Messages
9
Reaction score
0
I guess I dont understand. Even with the governor still connected it is plenty fast enough for me. At the end of that tutorial it says to connect the throttle directly to the carb. I can do this without disconnecting the governor right? Like i said using the arms on top of the carb to accelerate propels me to a top speed of 36 mph whereas the foot pedal only gets me to about 24 and im pretty sure is harder on my clutch because it doesnt get the rpms up there like it should on acceleration. Is there some way to link the throttle connect under the gas tank directly to the carb?
 

beansdaddy78

JR. Member
Messages
565
Reaction score
2
Location
Carbondale IL.
I guess I dont understand. Even with the governor still connected it is plenty fast enough for me. At the end of that tutorial it says to connect the throttle directly to the carb. I can do this without disconnecting the governor right? Like i said using the arms on top of the carb to accelerate propels me to a top speed of 36 mph whereas the foot pedal only gets me to about 24 and im pretty sure is harder on my clutch because it doesnt get the rpms up there like it should on acceleration. Is there some way to link the throttle connect under the gas tank directly to the carb?
i ran my throttle to my 5hp briggs, by taking of the pull start cover and running it through there the putting the cover back on. so far it still is working.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
I guess I dont understand. Even with the governor still connected it is plenty fast enough for me. At the end of that tutorial it says to connect the throttle directly to the carb. I can do this without disconnecting the governor right? Like i said using the arms on top of the carb to accelerate propels me to a top speed of 36 mph whereas the foot pedal only gets me to about 24 and im pretty sure is harder on my clutch because it doesnt get the rpms up there like it should on acceleration. Is there some way to link the throttle connect under the gas tank directly to the carb?

Based on the above information, I would suggest something is not right. There is either too much slack in your throttle cable, maybe your governor is out of adjustment, or perhaps something else.

Now- with regards to connecting directly to the carb WITHOUT removing the governor internals, I personally do not suggest it. The reasons are outlined in the above thread.
 

strikerty

New member
Messages
9
Reaction score
0
I got pissed off and went and bought a honda clone 212cc from tractor supply locally. Starting putting on tonight and unfortunately the gas tank hits the seat. . . Now I just have to figure out how to mount the gas tank someplace else and run a longer gas line to it . Thought about mounting it to the top of the rollover bars behind the seat but dislike the idea of gas pouring down my back and over my head if I do roll it . Could go and have the mounting plate cut free with a torch and reattached further back but that would require a larger investment and I already dropped 2 bills on the engine my wife is getting a little heated. . lol
 

strikerty

New member
Messages
9
Reaction score
0
OMG its SO FAST. Topped out at 40 running down a dirt road near my house. I know its spot on cause I have a gps speedometer on my smart phone. I think the clutch is gonna smoke soon even though its brand new. Its a cheap one Im going to have to have a machine shop make a bolt hole in the end of the shaft I just want to make sure its straight and then I can get one of the better clutches. I cant find any better ones that still have a key and a set screw they all have the key machined into the center which is good but this engine I bought doesnt have a bolt hole in the shaft.





 

Attachments

  • 0902121007.jpg
    0902121007.jpg
    8.5 KB · Views: 23
  • 0902122023a.jpg
    0902122023a.jpg
    5.5 KB · Views: 23
  • 0902122022a.jpg
    0902122022a.jpg
    4.9 KB · Views: 23
Last edited by a moderator:
Status
Not open for further replies.
Top