B&S generator engine on go cart

Status
Not open for further replies.

Nissinator1996

New member
Messages
54
Reaction score
0
I have a 4 hp generator engine I put on my go cart only problem is it has a tapered shaft....so I was thinking about cutting the tapered section off but that only would only leave with a 1.5 inch shaft with no keyway....would it work???
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
mine briggs came off a generator and also had a tapered shaft. The guy that had it before me used a file on it when it was running. Then he cut a key way with a cutting wheel but did not work out to well for me because he cut it crooked and the key came out when i ran at high rpms. So i decided to drill a hole through the shaft ( it was easy because i drilled on the flat part of the crooked key way) and through the clutch and put a bolt through it and a nut with some locktite. But i have had problems with the bolt breaking after a while so you would have to find something really strong that wont break to put through the hole. Or take it to a machine shop and have them cut out a key way for you.
 

Nissinator1996

New member
Messages
54
Reaction score
0
the shaft is 2.5 inches long 1.5 inches of it straight and not tapered so would that still leave enough room for a clutch...and do all clutches use keyways...???
 

Nissinator1996

New member
Messages
54
Reaction score
0
i have 3 other B&S engines that dont run at all but are good for parts so would it be easy to switch out the crankshafts???
 

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
i have 3 other B&S engines that dont run at all but are good for parts so would it be easy to switch out the crankshafts???

Not hard as long as the engines are similar (give us the model type codes off them and we'll tell you what should fit).

Swapping cranks is the best way to go. You will need a torque wrench though. :thumbsup:
 

B.M.800

TheBeal.
Messages
2,387
Reaction score
26
Location
Central PA
If you can get one of the other briggs running without difficulty, you could put that on the kart till you get the 4hp ready. I think thats what I would do.
 

Nissinator1996

New member
Messages
54
Reaction score
0
the other 3 i cant get running and would cost me some money that i dont have....1 have a broken piston....1 has 2 bolts broken off in the head where i tightend them to much from not having a torque wrench and 1 has a bolt broken off in the crankshaft...i have no idea where to find serial numbers on them and i think i might just take a file to it to get rid of the taper i dont wanna take the risk of taking it all apart and replacing the crankshaft and opening it up and losing compression im sure the gaskets would have to be replaced an i dont have a lot of money to work with i have to buy a clutch and chain still so trying to get rid of the taper and put a keyway the cheapest way possible..i can get 2 of the engines running if i can just get bolts out but dont have the right tools to do it
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
Filing is definately the cheapest and easiest way to fix your tapered shaft. Just make sure to file it evenly and take your time on it . You couldn't even tell my shaft filed down. And if your gonna change your gasket because your gonna file your shaft that isn't really necessary.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
No insult intended Tundra, but-

The guy that had it before me used a file on it ... cut a key way with a cutting wheel but ...he cut it crooked and the key came out when i ran at high rpms. So i decided to drill a hole through the shaft... But i have had problems with the bolt breaking after a while

You couldn't even tell my shaft filed down.

You're kidding, right?

Your shaft is not running true. This is exactly why you do this sort of thing properly. Either take the damm thing to a proper machine shop, or replace it with the appropriate crank. Your "filed" crank is now garbage.

AND- If you are opening up an engine (ie R&R crankshaft- then, YES- replace the gaskets as needed. The head gasket will probably survive the surgery, the sidecover gasket probably won't. Please note- a new sidecover gasket does not have to cost much. I make my own on a regular basis.
 

Nissinator1996

New member
Messages
54
Reaction score
0
well im going to the store tomorrow to buy a big file and im going to try and file it down hopefully it works out ...anyone know the best way cut a keyway into the shaft???
 

Nissinator1996

New member
Messages
54
Reaction score
0
i have and im pretty sure they will work but i dont want to tear apart the engine, replace crankshaft, replace gaskets, and put it all back together again when i can just try to file the crankshaft and if it doesnt work out or i dont like it then ill try and change the crankshaft
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
toystory how do you know my crank shaft is ruined? just because u cant tell its been filed? if u cant tell the shaft was filled that would be a good thing that means it was filed evenly and cleanly. This guy is looking for a cheap way to make a generator motor shaft fit a clutch. if u use a file then this will be a free fix. Machine shop may be too expensive and then he might run into problems putting the engine back together.
 

Nissinator1996

New member
Messages
54
Reaction score
0
toystory how do you know my crank shaft is ruined? just because u cant tell its been filed? if u cant tell the shaft was filled that would be a good thing that means it was filed evenly and cleanly. This guy is looking for a cheap way to make a generator motor shaft fit a clutch. if u use a file then this will be a free fix. Machine shop may be too expensive and then he might run into problems putting the engine back together.

Has a point
 

tundrabeagle3

New member
Messages
448
Reaction score
2
Location
Ca
is ur tapered shaft 3/4 on end of the shaft and torward the case? because thats how mine was and it made it much easier to file all he did was file it until it was level with the ends

heres a pic of the filed shaft


hows that for kidding?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
This guy is looking for a cheap way to make a generator motor shaft fit a clutch. if u use a file then this will be a free fix. Machine shop may be too expensive and then he might run into problems putting the engine back together.

What's cheaper? A gasket you can make yourself (or buy for a few dollars) & an hour or two of your time OR a big file to file down the shaft & an hour or two of your time?

I would swap out the shaft because, IMHO, you'll end up doing that when the file-down goes pear shaped.
 

Nissinator1996

New member
Messages
54
Reaction score
0
ive detemined im just going to tear apart the engine with tapered shaft and use it for parts with my original 5hp B&S engine to get it running again all i need is to get a broken bolt remover kit and some cork or gasket material and make some gaskets then it should run like a charm
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
toystory how do you know my crank shaft is ruined? just because u cant tell its been filed? if u cant tell the shaft was filled that would be a good thing that means it was filed evenly and cleanly. This guy is looking for a cheap way to make a generator motor shaft fit a clutch. if u use a file then this will be a free fix. Machine shop may be too expensive and then he might run into problems putting the engine back together.


Did you not read the quote package I posted? Your crank is ruined, said it yourself. All I did was shorten your own quote a bit to point out the important stuff... Plain as the nose on your face. I'm not meaning to pick on you, just trying to illustrate that an average person will not have much success "machining" a PTO with handtools. Just because it "looks" good, does not mean it is accurate. The naked eye is not capable of measuring down to thousandths of an inch. This is why god created precision machining tools.

Nissinator- good plan!
 
Status
Not open for further replies.
Top