Victa kart/performance mods

Status
Not open for further replies.

Ltdkc

New member
Messages
31
Reaction score
0
Hey guys. Just wondering if anyone here has done any successful performance mods on victa 160's. I've done some myself and I'm just wanting to get more ideas if anyone has any. I know some vintage kart blokes who have got decent power from 125's, but 160's are a bit neglected. I've applied similar principles from 125 mods to a couple of my 160' s and had some success and soon, I'm coming up to trying expansion chambers.
 

Ltdkc

New member
Messages
31
Reaction score
0
Some of the mods are, Yamaha yz 80 reed block welded into the victa 160 crankcase. The cylinder head is off of
Suzuki ts 100 from memory. The bolt pattern on it is very close to the victa one, so the benefits here are obviously a much larger head. More surface area for better cooling and also squish band combustion chamber which is far better than the original victa setup, and then there's the crankshaft which I've pressed some slightly oversized dia balsa wood Dowell into the holes in both crank halves and also crankpin, and piston pin, then covered the Dowell in jb weld all in the efforts to increase crankcase compression. I have an expansion chamber off a Yamaha 175 dirt bike to try out but I'd definitely like to try a properly designed one in the future. When I get my other cylinder back I'll post pics of the port mods.
 

Attachments

  • IMG_20170317_041439.jpg
    IMG_20170317_041439.jpg
    448.7 KB · Views: 6
  • IMG_20170317_041501.jpg
    IMG_20170317_041501.jpg
    358.7 KB · Views: 6
  • IMG_20170317_041621.jpg
    IMG_20170317_041621.jpg
    315.7 KB · Views: 2
  • IMG_20170317_041630.jpg
    IMG_20170317_041630.jpg
    335.4 KB · Views: 3
  • IMG_20170317_041652.jpg
    IMG_20170317_041652.jpg
    264.8 KB · Views: 5
  • IMG_20170317_043000.jpg
    IMG_20170317_043000.jpg
    295.4 KB · Views: 6
  • IMG_20170317_041805.jpg
    IMG_20170317_041805.jpg
    219.3 KB · Views: 3
Last edited:

Ltdkc

New member
Messages
31
Reaction score
0
Is sideways still an active member? He seems to be the a bit of a guru on all things victa
 

Ltdkc

New member
Messages
31
Reaction score
0
I'll end up using a tillotson, but I'll probly end up trying a dual carb setup with tillotson and a walbro on a progressive linkage, I'll probly try quad Walbros's and I'll try a 24mm mikuni.
 

Ltdkc

New member
Messages
31
Reaction score
0
And here is my vintage kart which will be running a hotty victa 125
 

Attachments

  • IMG_20170222_122356.jpg
    IMG_20170222_122356.jpg
    444.2 KB · Views: 8
  • IMG_20170222_122409.jpg
    IMG_20170222_122409.jpg
    426 KB · Views: 6
  • IMG_20170222_122427.jpg
    IMG_20170222_122427.jpg
    310.9 KB · Views: 5
  • IMG_20170222_122440.jpg
    IMG_20170222_122440.jpg
    495.5 KB · Views: 11

Ltdkc

New member
Messages
31
Reaction score
0
This is my late 60's Malvern star skidstar. It has my cylinder mounted reed valved victa 160 sitting in it. I'll end up getting a 5 speed hub, it's a 3 speed at the moment. And I'll run a torque converter. Paint it nice shiny red with lots of chrome.
 

Attachments

  • IMG_20170306_193343.jpg
    IMG_20170306_193343.jpg
    260.6 KB · Views: 4

sideways

Unfinished projects king.
Messages
1,501
Reaction score
2
Location
Perth, Western Australia
He was last active 01-05-2017, but you can send him a PM and see if he responds. PM's get sent to email adresses, so as long as he has the same email....he should get it

Different email but I drop in every few months and search for new posts about Victas.

Nice projects! Love the bike, always wanted to run a motor through a geared hub.

Keen to hear how the reed valve goes.

I dug out my Victas last night for a play. It's nice to go back to basic, cheap, fun stuff sometimes. I need to sort out my kart one of these days.

I was gonna make up a degree wheel and see what the port timings are, I lost my old info.
 

Ltdkc

New member
Messages
31
Reaction score
0
Hey sideways Good to hear from you. Ive been trying to get to you for a while now and here you are. You seem to be one ofthe few Victa gurus left in this world so its good to have you on hand for some advice. My number is 0490529867 if you want to chat about anything go fast Victa . Cheers
 

Ltdkc

New member
Messages
31
Reaction score
0
Victa mods

Here's some pics of the cylinder port work and crankcase mods I've done. As you can see, the transfer ports are now lengthened down to the bottom of the cylinder and the cylinder base and crankcase are both notched out and matched for nice flow of the fuel air charge. Also I've added a couple of alignment pegs on the top of the cylinder and notched some slits between the fins on the head so it lines up perfectly central on the cylinder.
 

Attachments

  • IMG_20170423_165429.jpg
    IMG_20170423_165429.jpg
    253.5 KB · Views: 5
  • IMG_20170423_165459.jpg
    IMG_20170423_165459.jpg
    259.7 KB · Views: 4
  • IMG_20170423_165511.jpg
    IMG_20170423_165511.jpg
    214.8 KB · Views: 3
  • IMG_20170423_165554.jpg
    IMG_20170423_165554.jpg
    237.8 KB · Views: 4
  • IMG_20170423_165657.jpg
    IMG_20170423_165657.jpg
    239.4 KB · Views: 4
Status
Not open for further replies.
Top