Master Hack
Well-known member
Hey this is my suc….ahhhh I mean customer.
Find yer own sukka!
Project Stoopid!
- Thread starter Master Hack
- Start date
Find yer own sukka!
Denny
Canned Monster
But, I’m just trying to help the poor guy out.
Hellion
Murderator
- Messages
- 9,153
- Reaction score
- 4,126
Blades hit something? Normal wear and tear? Poorly running engine with backfiring? Key was porous and crystalline from poor metallurgy? Loose flywheel nut? All probably a matter of time.
Hey, when did Stoopid go John Deere green?
Master Hack
Well-known member
No,no,no! British racing green!
might throw in sum yeller! Just like the Oregon Ducks.
There were no blades (it was on the NAG) it ran good ’til it didn’t.
Master Hack
Well-known member
We took a break from this stuff to have a test-n-tune/practice day.
The grandbrat came over for a few laps here @ the MTL prooving grounds.
found an exhaust leak, fixed that. He had a blast!
The grandbrat came over for a few laps here @ the MTL prooving grounds.
found an exhaust leak, fixed that. He had a blast!
Master Hack
Well-known member
Labor day weekend and it rained purdy much all weekend. Labor day is the beginning of the annual rain festival, it runs through July 5.
So we stayed in and completed another temporary final version of rear axle center section. I think we be closing in on the final final version at least temporarily.
l'm sure yer sick of the temporary final pics, but here's one more.
So we stayed in and completed another temporary final version of rear axle center section. I think we be closing in on the final final version at least temporarily.
l'm sure yer sick of the temporary final pics, but here's one more.
Master Hack
Well-known member
Update on the keyless lock tited flywheel.
It is working great after several hours of WOT abuse. The extra coupla degrees of advance helped a bunch
It is working great after several hours of WOT abuse. The extra coupla degrees of advance helped a bunch
Master Hack
Well-known member
Moving forward slowly...
Got chain now (50H) and a fresh dilenna. So where do you go when ya need expert opinions? DIYGK of course! So, here's the situation.
There is no chain adjustment. Can't move the engine and can't move the axle. A chain tensioner/adjuster Is in order. I pose the question to our panel of experts.
in the pic below ya can see the basic setup. The vertical tube is a tube in a tube.
The red arrow is a pin, the sprocket can move 1.5 inches (spring loaded).
I'll put a pivot at the bottom (yellow). that way the whole thing moves right to take up slack. (Yeah l know the chains too long) by 1 link. I can't take 2 cuz its too short. I will probably need a half link. The thing l need to decide is, should the bottom pivot be adjustable and lockable? Or should it be spring loaded?
Got chain now (50H) and a fresh dilenna. So where do you go when ya need expert opinions? DIYGK of course! So, here's the situation.
There is no chain adjustment. Can't move the engine and can't move the axle. A chain tensioner/adjuster Is in order. I pose the question to our panel of experts.
in the pic below ya can see the basic setup. The vertical tube is a tube in a tube.
The red arrow is a pin, the sprocket can move 1.5 inches (spring loaded).
I'll put a pivot at the bottom (yellow). that way the whole thing moves right to take up slack. (Yeah l know the chains too long) by 1 link. I can't take 2 cuz its too short. I will probably need a half link. The thing l need to decide is, should the bottom pivot be adjustable and lockable? Or should it be spring loaded?
panchothedog
Well-known member
- Messages
- 2,917
- Reaction score
- 3,950
I vote for adjustable and lockable. If it were a normal situation where chain tension was controlled by sliding the engine, would you want it spring loaded or bolt down tight?
Edwin Spangler
Well-known member
- Messages
- 1,037
- Reaction score
- 1,032
Isnt a spring loaded tensioner an issue when it comes to reversing? Suddenly all the slack is up top with nothing to take it up.
Ive always assumed thats why you see so many spring loaded tensioners on minibikes.
I recently made one and made it lock.
Side note: I would NEVER have believed that a skateboard wheel would have the durability to successfully be used as a tensioner roller. -But it works perfectly.
Ive always assumed thats why you see so many spring loaded tensioners on minibikes.
I recently made one and made it lock.
Side note: I would NEVER have believed that a skateboard wheel would have the durability to successfully be used as a tensioner roller. -But it works perfectly.