Need t/q help soon

Status
Not open for further replies.

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
torque converter help please................

Since this is my first t/c i am unsure, i bolted it to motor in the only position it allowed me to.
Its a duramax 7hp, i guess i need a smaller sprocket for it to clear bracket, i bought the same size sprocket that was on here when i got the kart. Heres some pics, the sprockets wont line up, the axle sprocket hits the bracket preventing it from sliding over.
The small sprocket side was already assembled when i got it.
I can try to get better pics if it helps.

Should i drop down the tooth count on the #41 or get a #35 sprocket ?

I am now not a happy camper
 

Attachments

  • d4c2b52f0854b930b96631881bab91d0.jpg
    d4c2b52f0854b930b96631881bab91d0.jpg
    213 KB · Views: 7
  • 91b1b9d234aa0cd95c51462cde4adc37.jpg
    91b1b9d234aa0cd95c51462cde4adc37.jpg
    248.8 KB · Views: 7
  • 63d46b5022e6da409f76c23463961f29.jpg
    63d46b5022e6da409f76c23463961f29.jpg
    234.5 KB · Views: 8
Last edited:

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Zoom out! Hard to put that into perspective. With all the additional bolt holes, can you not mount the CVT on another angle relative to the engine?
 

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
I'll get more pics but the setup only fits in one spot between the motormount and cylinder. Cant put towards front of motor cause it will hit seat and have no room to mount motor.
Hope these are better.
Am i doing something wrong ? :huh:
 

Attachments

  • 2012-09-16_12-23-23_756.jpg
    2012-09-16_12-23-23_756.jpg
    123 KB · Views: 11
  • 2012-09-16_12-22-56_123.jpg
    2012-09-16_12-22-56_123.jpg
    94.1 KB · Views: 5
  • 2012-09-16_12-22-24_754.jpg
    2012-09-16_12-22-24_754.jpg
    113.8 KB · Views: 8
  • 2012-09-16_12-21-57_348.jpg
    2012-09-16_12-21-57_348.jpg
    94.8 KB · Views: 5
  • 2012-09-16_12-20-51_339.jpg
    2012-09-16_12-20-51_339.jpg
    102.4 KB · Views: 8

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
If need be for chain clearance you can trim part of the mount. Additionally you may consider using #420 chain for width.

If all else fails you may end up purchasing a jackshaft, bearing mounts, bearings, new jackshaft sprocket, and a new belt for the adjusted distance.

There are cases where the on board mounting plate just doesn't work.
 

ML-TOYS

New member
Messages
2,908
Reaction score
21
Location
long island, new york
If need be for chain clearance you can trim part of the mount. Additionally you may consider using #420 chain for width.

If all else fails you may end up purchasing a jackshaft, bearing mounts, bearings, new jackshaft sprocket, and a new belt for the adjusted distance.

There are cases where the on board mounting plate just doesn't work.

Thanks or the info, think i will just get the #35 sprocket.
I just spent 180 bucks on the kit i really dont feel like dropping a whole bunch more on this.
If all else fails you may end up purchasing a jackshaft, bearing mounts, bearings, new jackshaft sprocket, and a new belt for the adjusted distance.
 

Blazkowiez

Kart Aficionado
Messages
2,538
Reaction score
48
Location
Houston, Texas
Aside from the belt which is a wear part that solution seems to sound cheaper to me than purchasing a new drive sprocket, jackshaft sprocket, and chain.
 
Status
Not open for further replies.
Top