Engine sputters on Honda GX200

Status
Not open for further replies.

gallagher19

New member
Messages
172
Reaction score
0
Location
Fonthill, Ontario, Canada
Hey guys. I need some help once again. My engine has been running awesome for the past couple of months now. But all of the sudden it started to sputter once in warms up, like about lap 6. Run good prior to that. I have put in a new plug, cleaned carb thoroughly 3 times, new plastic piece between head and carb. Now I notice that when I run it with no load it seems to have a slight miss at top end. What the heck could this be all of the sudden. Any input is DEFINITELY appreciated. Thanks
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
was/is the engine modified (governor removal, intake/exhaust enhanced.. rejetted or swapped carb etc?)

Run it again for six laps and after it starts acting up on you, pull the plug and take a pic of it.
since it's a fresh plug reading can be difficult unless it's wet
if it's wet your running too rich and you should lean it out a hair.

Same thing can happen if the airfilter is blocked (clean it after ever 4-5hrs of driving)

if your plug is dry and it's nearly white, you run too lean or you have a temp leak;
can happen if the gasket between the cylinder head and the plastic manifold is broken or just bad.
unlikely the one between the manifold and the carb (there's less heat difference between the parts) but unlikely doesn't mean impossible, so check both of them.

but first as soon as the engine is acting up, get off the kart (engine running) remove the chain (or jack up the rear) and rev the engine to have it sputter..
then wiggle the carb slightly to see if that makes a difference (if so, gasket or just not bolted down correctly)

'sid
 

gallagher19

New member
Messages
172
Reaction score
0
Location
Fonthill, Ontario, Canada
Thanks. Plug looks good. Will take picture later today if it acts up again. Air filter gets cleaned after every race. Yes engine is modified with muffler, jet, and air filter, governor off and a few other mods which I have no idea what was done to it.

I changed my plug wire and coil. Someone told me that if the wire is cracked it will do that once it gets warm. Hoping that works. We'll see later today when I go out on the track.

If not I will check the gaskets. They are all new and the carb is nice and tight. I put all new gaskets in also, but who knows will check that and the plastic (even though it is new also)
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
if you replaced all the gaskts, and the intake manifold (cough unifold ;)) is new as well..
the only thing is that you by accident swapped the two manifold gaskets (I doubt you did)
since the one on the carb side has an additional cutout that wouldn't make any sense on the engine side...

but truth is, if swapped the fuel bowl isn't able to refill properly because of the blocked vent-hole (especially if the other one is also blocked.. say by a K&N style filter adaptor without vent)
but that should happen at all high rpms, not just after the engine warms up IMHO.

So yeah, unlikely, but still a possibility.

'sid
 
Last edited:

gallagher19

New member
Messages
172
Reaction score
0
Location
Fonthill, Ontario, Canada
ok, so I tried everything you said and the darn engine still acts up after 7 laps on my track. Driving me nuts. Worked perfect before. I found out from my (crew chief) LOL that the fuel he was giving me was HIGH OCTANE!!! Therefore my plug was getting hot. I went to a colder plug and that didn't work. Than I decided to go back to the original plug (new of course) and put regular fuel back in it. But, I decided to put in a larger jet (in case it was fuel delivery). It still freakin cuts out and misses like crazy once the engine is warmed up and at full throttle. It doesn't seem to be a fuel delivery issue. It seems to be cutting out (electrical).

To answer your original question: Governor is OUT. K&N air filter, muffler and yes the guy who had it before had some work done to it, but I have NO FREAKIN IDEA WHAT he had done to it. All I know is that for the first 4 races we had here it was AWESOME!!!

In saying that I do notice another issue. When I have it on the stand and start it up (first pull every time) it starts to miss a little bit when I hold the throttle steady 3/4 or full. Didn't do that before. Not sure why.

I am at the point of ready to take it to a shop. It has a lot of compression and there's abolutely no sign of any debris or shavings in either the oil or the plug when I change it. Which is after every race. HELP!!!!!!!!!!!!:surrender:
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
hmmm...

a nearly-sheared flywheel key perhaps
but that's not more than a wild guess I'm afraid.

Since I don't see how it works properly when cold but misses when hot...
but since you basically only need to remove the airshroud to see how the magnet lines up
(maybe the starter cup etc. to get a glimplse at the woodruff key)
it doesn't harm to take a look.

It also wouldn't harm to check all the ignition parts.
magneto gap, cable and boot again...

maybe it's a heat expanding crack that looses contact..
but tbh... that too is nothing more than a wild guess

Sorry.. I hope someone else will chime in that had (and fixed) a similar issue.
Or has just a better idea than me.

Just to be safe.. I'd check the valve lash again, it should sputter when it's incorrect not just miss to ignite at times IMHO;
but since there is something wrong, the easier checks can be performed first,
so that when you eventually found the issue, you know the engine is not only fixed but properly maintained as well :D

'sid
 

chancer

ɔ ɥ ɐ u ɔ ǝ ɹ
Messages
9,358
Reaction score
97
Location
COMFORT, TEXAS
I used to work on stock cars. If a car stalled half way through a race, say after a mild wreck, it would be very difficult to start. Why I asked.
If I remember: The heat of the car made it difficult for the amps to get to the starter.

I wonder if you have a weakened or heat damaged plug wire,( or other wiring) but it only shows up after 7 laps due to excessive heat.
Just a thought.
 

gallagher19

New member
Messages
172
Reaction score
0
Location
Fonthill, Ontario, Canada
Thanks guys. I will check all the above items all three of you mentioned. Very possible and I really hope that one of you are correct. It's so weird. Will try tonight or tomorrow night and see if that helps.
 
Status
Not open for further replies.
Top