Cereal Box Gaskets

Status
Not open for further replies.

souperman000

New member
Messages
2,466
Reaction score
11
Location
Westlake Village, CA
So I did a quick search on the forum to look up homeade gaskets after people have mentioned them in some posts.

The gasket between my airfilter "housing" and my carb ripped while I was putting it back on :oops:. I have read up on cereal box gaskets and everyone recommends them.

Is there a trick to it or do you just trace it on a cereal box and then cut it out? I have a feeling I'll find a way to mess it up and hurt the engine...

Thanks,
Soup
 

r_chez_08

Should be in the shop...
Messages
4,827
Reaction score
14
Location
Cornwall, UK
Pretty much just trace it and cut it out. Make sure no gasket is obstructing. A leather punch and hammer helps but is not neccesary. It works OK.
 

Bluethunder3320

New member
Messages
5,677
Reaction score
39
that gasket is only in contact with air. doesnt even get hot. so it doesnt have to be perfect.

sometimes i have put some black motor oil around the surface, stamp the cereal box in it, then just cut it out. or you can trace it.

use a knife or xacto blade it would come out the neatest


had to make one of these gaskets about a week ago, i got lazy and just put some silicone on it.... it will run without the gasket here anyways
 

souperman000

New member
Messages
2,466
Reaction score
11
Location
Westlake Village, CA
My first attempt. It fits pretty well may be not the exact same size (tried my best) will that affect anything?
 

Attachments

  • SAM_1017.jpg
    SAM_1017.jpg
    69.7 KB · Views: 10
  • SAM_1019.jpg
    SAM_1019.jpg
    100.1 KB · Views: 13

oldbikerarlo

Old guy
Messages
449
Reaction score
2
Location
Marana, Az.
Looks good, I use a Rand Mc. map book the cover for thick gaskets and inside pages for thin gaskets. When I was in the Navy we often used chart paper.
 

Doc Sprocket

*********
Messages
15,677
Reaction score
153
Location
Ontario, Canada
Looks good, I use a Rand Mc. map book the cover for thick gaskets and inside pages for thin gaskets. When I was in the Navy we often used chart paper.

Gonna suck if your GPS breaks, and the street you're looking for is behind your manifold!!!! :roflol:

I've been making my own gaskets for a long time. Some tricks I use to transfer the pattern-

Using dirty fingers to rub the gasket paper over the part- kinda like a charcoal rub.

When your fingers are actually clean, rub harder and over all the edges to crease the paper.

Use a little motor oil, machinist's dye, or other visible substance on the part, and press and release on the paper- like a stamp.

I use leather punches to make the holes. I have also used a single hole, office-style paper punch to make the holes. Careful work with a hobby knife will do, too.

I often give paper gaskets a light coat of fresh motor oil on both sides just before installation to swell the fibres a bit- can improve the seal.

When cleaning the gasket surfaces prior to installation, be very careful to not scratch, gouge, or nick the surfaces. Get ALL traces of old gasket material off, too.

When I make a gasket, I often use the new gasket as a template to make a second one- that way the next time I rip into that engine, I don't have to take the time to make a gasket if I am in a hurry.

A hunk of rubber bicycle innertube is brilliant for carb-manifold gaskets and other non high-heat, less torque sensitive applications.
 

crazyman

New member
Messages
239
Reaction score
1
Location
Yorkville Il
A rounded handle from a screwdriver pressed over holes makes a nice imprint too.

I've used all different kinds and thicknesses of cardboard.
 

fowler

New member
Messages
5,463
Reaction score
18
Location
Bullsbrook West Aus
Usually to make the gaskets I put a peice of gasket paper over the hole and tap the edges with a hammer to break the paper
But not too hard and not on ally

And I can vouch for the rubber gaskets
We use them a lot as a tempory option

wad punches are the best way to make holes
 
Status
Not open for further replies.
Top